castor issue

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 25, 2007
Threads
22
Messages
144
Location
puyallup, washington
94 80 with j springs and 2 inch spacer in the front

left castor -2.01 right is -2.5. i have ome yellow bushings

queston can i use castor plates with the bushings to get back to the proper angles or would that be to much.. i dont know how many degrees the plates are. can any one tell me how many degrees either slee plates or landtanks plates will give this truck is crazy to drive right now any help would be great thanks:bang:
 
There really needs to be a note in the FAQ or somewhere that with these type of questions a hub to fender measurement should be given along with the type of springs, caster, etc.

Rick is correct though. Usally 5" OME comp or 850J's with 2" spacers set at or above the hight of 6" springs such as Slee's which is in the 25" hub to fender range. There are pretty much two choices, new arms or the drop bracket with bushing solution.

Since you have the bushings, it would be simple to add the Man-A-Fre drop brackets. Not the most ideal solution but the simplest.

One point that hasn't been mentioned in all the caster posts is the fact that having the rear set higher, "stink bug" will lower the caster up front also. This is something to keep in mind. I've gotten away with using Rick's caster plates with 25" up front but my truck sets bearly 1/2" higher in the back. I'm near zero but mine isn't a DD either so I'm not too worried about it. It tracks good and straight but I wouldn't want to be dodging everyday freeway traffic in it.
 
castor

my hub center to fender is 25 inches. the truck sits high in the rear it 2 inches higher. it has arb bumper winch and dual batteries in the front. i dont want to use the drop brakets should i just put the old arms in with factory bushings and then use the plates. as for the arms they are just not in my budget at all for a long time.
 
the best way is to slot the front holes which will give you 2.5 deg as well as 3 deg bushes, instead of 2 deg, this will get you to spec.

To clear the control arms with the steering arm, you can grind off the high cast ridge on most of them, doesnt weaken the arm, and/or you can press the steering arms from the knuckle to bend them up slightly to clear. They are cast steel, so bend pretty easy.

We find they drive best at height with aprox 2.5 deg castor for better hwy straight tracking, and return to centre.
 
heres a pic of my lifted cruiser...i have the same setup as yours...only i sit level....25 from center hub to fender...drives straight ,,,every so often starts to wander off a little....still havnt did anything to correct castor....i mi
100_0107.jpg
ght do man a fre drop brkts ...
 
my hub center to fender is 25 inches. the truck sits high in the rear it 2 inches higher. it has arb bumper winch and dual batteries in the front. i dont want to use the drop brakets should i just put the old arms in with factory bushings and then use the plates. as for the arms they are just not in my budget at all for a long time.

by my calculations you need somewhere in the neighborhood of 8* of caster correction. Caster plates yield 5* so with them installed you'll be around 0* of caster and that is really kind of low.

now if you were to pull the rear spacer and swap in a 1" spacer in front you would have about a 1" rake and the plates would bring you in at around 2* caster and you would be setup for a DC shaft to control vibs.

The limiting factor with rotating the axle is the tierod hitting the arms. So if Slee's arms are out then the best next solution is plates. So if you were to install the plates and felt that the truck drove unacceptably bad the above solution would be the route I would take to correct it.
 
heres a pic of my lifted cruiser...i have the same setup as yours...only i sit level....25 from center hub to fender...drives straight ,,,every so often starts to wander off a little....still havnt did anything to correct castor....i might do man a fre drop brkts ...

The one nice thing about the drop brackets is that you can then add bushings to them. I'd avoid the 3" drop brackets as they fall in where you might get some vibs that neither drive shaft can solve.
 
I saw a option change your control arms ( with already OME in ) with other Mud mate that don't have 'em but don't need more caster ..

So then with the new ( to you ) control arms and factory bushings run the caster plates .. I'm higly satisfied with 'em.
 
i have 2 sets of arms one with yellow bushings and one with factory ones. if i could just change the arms back and add castor plates that would be great. and i could offset the cost if i sell the other arms. any thoughts
 
If you can get even 1 degree of positive you will be much more happy with the way it drives. If you want to play with it, get a magnetic protractor, a couple of 1/2" bolts and nuts. Park on a relatively level ground, install the bolts in the holes in the arm brackets as in the pic, remove the front side arm bolts, put the protractor on the arm brackets and use the 1/2" bolts as jacks to rotate the axle. Move it 4 degrees or so and see if everything clears.

With the stock arms the biggest problem that may not allow enough rotation, is arm to tie rod clearance, some clearance can be gained by grinding on the arms. If you fab there are a couple of options; The "old school method" is to slot/drill the brackets and tack weld washers to the brackets, relocating the bolts.

http://www.lcool.org/technical/80_series/caster_mods.html

Some have made adjustable setup like this one;

https://forum.ih8mud.com/80-series-tech/14506-adjustable-caster-modification-final-picture.html

arms_1.jpg
 
With my actual setup .. ( would take some pics tomorrow ) I have no clearance issues with the Slee caster plates ..
 
Back
Top Bottom