Caster Correction - Help!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 28, 2004
Threads
37
Messages
249
Location
Richmond, VA
I have the Slee 2.5" medium lift OME kit which includes the OME caster bushings. I have those bushings installed. I have the Slee drag link (SOF1027) and the Slee tie rod (SOF 1028). I'm running Nitto Terra Grappler 305/75-16s (33") tires and I have a very squirrelly truck!

The last time I had my caster checked, it was 1.4-1.5*, which is a bit low. I'm going to take it to get it rechecked in the next couple of days, but it shouldn't have changed (or enough to matter). I need to get that up to 3* or so to get some stability back in my rig. But how do I do this? In reading, Slee's plates are setup for 4" lift, so probably too much correction for me. Landtank's plates end up making about a 5* change from what I read, so too much there. Obviously OME bushings didn't make a difference.

What are my options?
 
Toe seems to be in spec (about 0.09 left and 0.14 right) but I'm going to check that too.

What are the specs on the OME bushings and Slee's bushings? How much do that add total? (so basically, what is my caster without the OMEs so I know what I will be starting from).
 
Stresspup, go with slee's 3 deg. bushings (blue bushings)
I just put these on with my new lift 850's front ..860's rear
runs like stock no vibs. If you can make front caster jig, it will help when you put control arms back on.. here's a couple of pics of mine
scott
IMG_0556.webp

IMG_0558.webp
IMG_0556.webp
IMG_0558.webp
 
Yeah, I'm not looking forward to putting the arms back on. When I did it with the OME bushings, I had everything strapped down so it wouldn't move and it did anyway! I had to hook up a come-along to an anchor point in my garage and crank it slowly to get things to line back up.

How did you keep yours from moving? How did/do you use your plate?
 
All I have is Slee's blue bushings in mine and I have 850J's with Slee's 1" spacer! No idea what my actual caster numbers are, but it feels like it did when stock with no vibes.
My wife would let me know if it felt at all different, so I do not feel the need to dump the $$ for plates, a DC shaft and the possiblity that I still would have vibes.

TK

edit: I should also piont out that I have an ARB and M12000 to wiegh down the front end.
 
Hey, maybe that is what I need! Blue bushings and an ARB! I'll tell my wife I HAVE to have that to help fix the steering. Wonder if she'll buy it. (wonder if it would help at all...)
 
I built this plate with the stock bushings still in it to get the right hole spacing.Take out old bushings then press first blue bushing in with-out jig.(make sure its in the correct position) Then put control arm in jig with 1st bushing pressed in right location, use jig to press 2nd bushing in so you get perfect bolt hole alignment. Mine bolted right up without any problems, and drives great, no vibs!
Scott
 
no need to get fancy with a jig, I have press templates for Slee's blue bushings. Even if you strap down the axle in position it will have to be moved as the bushings want to rotate the axle from it's original position. One of the easier methods is to bolt the arm to the axle and then bolt it to the frame. Either way you need to wrestle things into place.
 
Since I already have the OME caster correction bushings in, and I don't have a jig, how do I go about lining the bushings up in the control arm to make sure they are right?

I put the OME stuff in about 2 1/2 years ago (yes, driving a squirelly rig for too long now!) so having to dig in the memory banks for how I did things....

On a semi-serious note, would adding the weight of the ARB in the front actually add some positive caster? Would that bumper be too much for the medium setup I have?
 
The ARB would definitely help to give you positive castor. You could also work on dual battery setup, winch, ARB air compressor, at the list goes on... However, your mediums may sag a bit with the non-winch ARB. Others that have mediums will pipe up soon.

TK
 
ARB and winch is the most I would probably do. Don't want to overload the mediums, but I would definitely be interested to know if this would help and not be too much.
 
I have rebuilt the front axle and I was pretty sure I snugged them properly, but I'm up for checking. What is the proper "snugness" and how to do I verify?

But even if they need a little bit of tightening, caster is still off and needs some attention.
 
I have rebuilt the front axle and I was pretty sure I snugged them properly, but I'm up for checking. What is the proper "snugness" and how to do I verify?

But even if they need a little bit of tightening, caster is still off and needs some attention.

I don't recall the proper fish scale spec, I do mine by feel. When the bearings are repacked, I tighten it up good, spin the hub a few times then back off the nut, then re-tighten to "feel" while spinning the hub.
FSM has the spec.

Agreed your castor is off, but not by much. "squirrelly" leads me to think it's possibly something more besides just a little off on castor. Never hurts to check.
 
I don't recall the proper fish scale spec, I do mine by feel. When the bearings are repacked, I tighten it up good, spin the hub a few times then back off the nut, then re-tighten to "feel" while spinning the hub.
FSM has the spec.

Agreed your castor is off, but not by much. "squirrelly" leads me to think it's possibly something more besides just a little off on castor. Never hurts to check.

Before I castor corrected my rig, it was very "squirrelly" i.e. it tracked grooves in the road, felt darty at speed, and generally felt like driving my 1971 FJ-40 on ice.

TK
 
Before I castor corrected my rig, it was very "squirrelly" i.e. it tracked grooves in the road, felt darty at speed, and generally felt like driving my 1971 FJ-40 on ice.

TK

That is exactly how I would describe mine. Tracking grooves (feels that way anyway) and darty at speed.

So, do I go the blue bushing route, or Landtanks plates with factory bushings? Both require pushing out bushings and new ones in, and I'd really prefer not to do that more than once if possible! :)
 
Back
Top Bottom