Carb help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 3, 2017
Threads
21
Messages
281
Location
Norcal
Guys,
Struggling to get this guy running. The carb is brand new and the truck sat in a field for 20 years. New fuel filter, spark plugs, dizzy cap, cooling system, etc. Trying to get it running strong, but I either have a vacuum leak or something. The beginning of the videos show the pop of the carb. Please check out the attached videos with the sound. When I step on the gas, it works some times, the other times it seems to backfire at the carb. I have tried a lot of the things in the other threads, but can't dial it in. Any advice? Thank you in advance!


 
Ok, timing was off and it runs better with no pop from the carb. However, now it seems to miss if I try to drive...maybe not miss, but skips as I try to accelerate. Could that be a carb that isn't adjusted correctly? If I raise or lower the idle, the timing changes. Maybe a vacuum leak? Thanks!
 
Fuel Cut solenoid


1587780236666.webp
 
Back out there this morning...timing is right at 7 and it still sputters. I pulled the vacuum advance line off the carb, set the timing, put the vacuum advance back on and no luck:
 
You may want to try removing spark plug wires at the spark plug at each cylinder. Do one at a time and see if that cylinder is firing. Should have a good yellowish blue spark. Also pay attention to if the engine rpm changes . If you pull a wire and you get no change that means that that cylinder is not firing . See if that points you in a direction
 
I pulled all the wires and have good spark. When I pulled the number 6 cylinder wire, the engine rpm dropped and the motor almost died. The only one that happened with is the 6th cylinder. Each of the other wires that I pulled did not result in any rpm change.
 
Went to Ace to get a 1/8” adapter for the manifold to check the vacuum. Pretty sure it is an NPT adapter but doesn’t fit...is there a different thread type? Any idea where to get the adapter to screw into the manifold with a nipple to check the vacuum?
I suspect I’ll have to adjust the valves if that #6 cylinder isn’t working correctly? Any help is greatly appreciated.
 
it is not NPT thread in the manifold. 1/8 NPT will almost fit if you force it. Better to run a tap down that hole. Easier to hook your vacuum gauge to the hose that goes to the brake booster.
 
The thread is 1/8 BSPT. As Pighead mentioned some folks make NPT work. Mark's Off Road in Burbank would have the correct BSPT fitting. He does have a $100 minimum order though. He sells a kit to convert your distributor from points to electronic ignition. That would meet the minimum if you are interested in ditching points. Mark's # 1 (818) 953-9230. Just leave a message and he'll call you back.
Sounds to me like your spark is off. Might not hurt to post up a picture of your dissy. Did you only replace the dissy cap? Make sure if you ever pull the dissy you fully seat the tip into the oil pump. Seen quite a few threads where guys seize engines due no oil pressure.
 
Mark's # 1 (818) 953-9230. Just leave a message and he'll call you back.

Just FYI, Mark's mother is in hospice care as of today, so don't be surprised if it takes much longer than usual for him to call back.
 
@Advrider639 working on it. Trying to get a fitting for the exhaust manifold...the one from the brake booster is bigger than my vacuum gauge...so, working on it. (probably easier to get an adapter for the brake booster line to my gauge). Ran into an unrelated issue with brake master cylinder leaking because it's old and I just swapped out the front drums to disk on then master cylinder started to leak, etc.
 
If the engine is running, your timing can’t be too bad. I would move on to other potential causes.

It has got to be a vacuum leak. Have you inspected your manifolds; any carbon build up, cracks, warping? Spray some carb cleaner around the manifold and head, what do the RPMs do?

Have you adjusted valves?
 
@Advrider639 Vacuum leak checks will be later today. The engine was from 1980 FJ40 into this 1975 done by the PO. I desmogged (I'm in CA) and attempted to plug all the holes. I haven't done any of the vacuum leak checks yet (will start later). I have not adjusted the valves either. The valve adjustment probably needs to be done so that's probably next on the list. I'll report back with what I find.
 
Valve adjustment should be first on your list. Second also. First when it's cold, again when it's warm. Everything else depends on it.
 
Back
Top Bottom