Specter maybe?
BSLCA BS... ie.. local chat..
- Thread starter PScottBx
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Specter maybe?
Got some new wheels coming for the Toyota. Got to love stock rims with no rust from the mid-west.
Last edited:
- Thread starter
- #2,683
Nice....
me
me
Another set of factory chrome wheels? Lucky dawg
I was looking for some when I bougth my black steel wheels, Went to the junk yard by Hampton toyota... that joker wanted 600 for a set. I got my steelies for I think 250 shipped from jegs.
- Thread starter
- #2,686
Dim thinks that all his sh*t over there is gold. It's not junk at all in his eyes. He has a couple of cruisers over there as well....hidden.
me
I need yall to say a little prayer from my 4runner. I am about to hack up the Driveshaft to try to make my Square driveshaft for the 4th of July run.
on a side note, I think I figured out part of the reason my truck has been running so poorly. I have always heard a vacume leak but could never find it, last week in Lafayette it all of a sudden got to the point the engine wouldn't run under 1500 rpm at all and had to pump the gas to get it to start. got it home and started looking. When I set my hand on the carb it shifted to the side almost a 1/4 . Apparently the locktite I used when I installed my webber sucked because all the nuts had backed them selves out. All but one of them was not even finger tight. got them snugged and it is running alot better again
on a side note, I think I figured out part of the reason my truck has been running so poorly. I have always heard a vacume leak but could never find it, last week in Lafayette it all of a sudden got to the point the engine wouldn't run under 1500 rpm at all and had to pump the gas to get it to start. got it home and started looking. When I set my hand on the carb it shifted to the side almost a 1/4 . Apparently the locktite I used when I installed my webber sucked because all the nuts had backed them selves out. All but one of them was not even finger tight. got them snugged and it is running alot better again
- Thread starter
- #2,688
Best kinda "fixes" are free!
Good luck ...and I can already hear the clank clank...
Bx
Good luck ...and I can already hear the clank clank...
Bx
Well Things where going good till I ran out of sawzall blades... And clank? what are you talking about? with all the racket my truck makes I wonder if I will even notice
Greek (sport?) Utility Vehicles Of Interest
OK guys, as promised. Hit the Image Hosting... link below and ENJOY!
Prize
to those who can identify the Greek LGTV (Live-Goat Transport Vehicle) among the samples.
Image hosting, free photo sharing & video sharing at Photobucket
Cheers,
OK guys, as promised. Hit the Image Hosting... link below and ENJOY!
Prize
to those who can identify the Greek LGTV (Live-Goat Transport Vehicle) among the samples.Image hosting, free photo sharing & video sharing at Photobucket
Cheers,
- Thread starter
- #2,691
Sweet! I like the Unimogs
Thanks
Bx
Thanks
Bx
Great pics Ricardo X2 on the Unimog shots. I hope you'll post some of those great shots of the ruins in our traveling thread they'll make a great addition. 
Props on wearing the shirt to Greece!
Great pics Ricardo X2 on the Unimog shots. I hope you'll post some of those great shots of the ruins in our traveling thread they'll make a great addition.
Your wish is my command, check out the travel thread.
Well Things where going good till I ran out of sawzall blades... And clank? what are you talking about? with all the racket my truck makes I wonder if I will even notice
Why do y'all mess with major **** right before big rides?
if my front diff is leaking out near the pinion shaft near the yoke, what part do i need?
http://www.sor.com/shared/image/090a.gif
from specter, 26 is the shim set and 29 is the "Pinion Seal"
thats all i should need, correct?
http://www.sor.com/shared/image/090a.gif
from specter, 26 is the shim set and 29 is the "Pinion Seal"
thats all i should need, correct?
I just ordered 29 for the same problem. I have not changed it out yet.
Because I had been putting this off since the last time I went to S.I. When you wern't following us, I had to borrow toold formt he J##p guys twice to put my Driveshaft back together, then again @ the Crawfish boil, and AGAIN in Gilmer before that.
New shaft has 4 inches of available compression, and about 8 inches of extension. If I pull this baby apart I am in a bind.
Yep just the pinion seal. You may be able to find it at O'Reilly if you don't have time to order. They use to stock it here on the Johnston St store either way they can probably get it to you over night.