Breaking in a "new" Motor

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 22, 2003
Threads
284
Messages
8,118
Location
Kansastitty
If you had a "new", as in rebuilt, 2F, bored, new pistons/rings, cam, lifters, seats, bearings, etc.

1. What oil would you use for break-in?

2. How many miles before oil change?

3. Breaking in cam and lifters....2,000 rpm for how long after first start up?



It was all put together with Assembly Lube, so I was warned not to freak at the first oil change.

I'm gettin' close.


Ed
 
break in

Degnol i read somewhere in toy manual no idleing for long periods no lugging of motor for first 2k mi. I rebuilt mine [havent started yet] oil is 5 w 30 for break in as iol is big $ now and it takes lots , i will change at 2k mi to 10 /40 , i am still at least a year from finishing the body on my 78 40 , this has worked for me on many a 350 chev with no problems mark :beer:










78 fj40 times two
73 fj 55 parts car
 
Good high quality 5w30 oil for break-in works well.
Usually 1500-2000 miles before first change is sufficient. Change oil and filter and check for metal in the oil.
For cam break-in run at high idle 1500-2,000 rpm for an hour varying the speed up and down often and check everything very carefully for that time. Watch oil pressure, temp, check for leaks and listen for funny (not ha ha funny) sounds.
After initial break-in keep the idle set relatively fast (1200-1500) for the first 500 miles and 1000 for the first 1000 miles Avoid long periods of idling as well as lugging the engine and long preiods of high or constant speed. Vary your driving speed for the first 1000 miles or so
It wont hurt to keep the idle up a little for the first 2000 miles to keep more oil movement in the engine .
 
Degnol said:
If you had a "new", as in rebuilt, 2F, bored, new pistons/rings, cam, lifters, seats, bearings, etc.

1. What oil would you use for break-in?

2. How many miles before oil change?

3. Breaking in cam and lifters....2,000 rpm for how long after first start up?

Ed

If someone else built it, follow their recommendations (aviods warranty issues)
Personally, I'd run 15W40, change oil and filter at 500.
20 mins for the cam is ussually suffucient
 
I've always dropped the first fill and filter at 100 miles but I get really anal with a new engine. My reasoning is that the bulk of the bearing breakin wear happens very fast initially and then tapers off as breakin proceeds. I want to remove any particulate metals from circulation as soon as it's rational to think that there might be some to remove.
If someone lets me alone I might change the intitial fill within the first five minutes of run time, but that's just craziness...........probably.
 
We use NAPA straight 30w. I spin up the dist to pressure then fire the truck up and get it to med/fast idle like 1200rpm or so until it hits temp then run it through a few cycles of fast/slow idle maybe for 20 min or so then kill it and change the oil and filter.

Refill with the same stuff get it running and tuned then drive it in differnt RPM cycles for a few days. I dont worrk so much about miles as I do time and conditions but more or less 100 miles.

Change it out with either 10w-30 or 15w-40 then drive it normally for around 1k then change it again.

I guess it is a bit anal but oil is cheap and i have found some weird stuff in it soon after start up.
 
Oil is relatively cheap - cheaper than a new motor...

Change oil and filter after first 500 miles...

Pressurize oil system before initial start.

Vary load - accelerate, then de-celerate - on and off, over and over. Helps rings and valve guides...

Fresh gasoline!
 
Why would a motor that is new have problems with long periods of idle... just wondering why. I have always known to run the motor fast for the break in but I dont know why?

Sorry for the high-jack

Rezarf <><
 
Break in cam (20-30 minutes), THEN change oil/filter. After that you're good for a longer run.
 
Rice said:
Break in cam (20-30 minutes), THEN change oil/filter. After that you're good for a longer run.


For the couple of engine rebuilds I've done (2F & 3FE) this is the approach I've taken, and I'll be doing it this way on the 2F I'm currently putting together. I also go in and retorque the head bolts after a few hundred miles.
 
Tanks, all.

Ed
 
Back
Top Bottom