Brake Caliper

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 2, 2007
Threads
21
Messages
42
My front brake caliper pistons are not retracting far enough to install new pads. Any helpful tips? The dealership needed my VIN# when I bought the pads because there are two different pads for a 96. The worn pads and new pads are of identical shape, I just wonder if the difference between the two pads available could be the thickness. I just want to pick you brains for info. Besides its too damm cold to work on the brakes now. Snowy and cold in Boulder CO.
 
How are you shoving the pistons in? I like to use a C-clamp, with the bleed screw open so I don't push fluid backward. Usually I put the C-clamp on the caliper before loosening anything, with it's swivel pad on the outer brake pad, pushing the pads into the caliper. Sometimes, like tonight on a Jetta, the piston doesn't go in far enough, and I have to use the C-clamp directly on the piston when the pads don't quite fit. With dual-piston brakes, you'll need to put something across them to push them both in together. The old pad works, but I hate to mess it up in case I need to put it back in. That's why I like to push on the back of the outer pad at the beginning of the job.
 
Use the old pad to apply pressure to both, do one side at a time

My friend showed me this cool inflatable pouch he has that is alot like a bloodpressure cuff but flat which he uses, but I don't have such luxuries and now use a C clamp.
 
Make sure you clamp off the line and release the bleed screw. If not you can destroy the ABS module.
 
Funny, Im in this senario right now. However mine is a frozen piston. $101 ($50 core) from a local shop.
 
Just fininshed with my caliper replacement. This is the easiest brake jobe I have ever done. I was stunned by its simplicity and function. Chalk up another one for Toyota.
 
Last edited:
Make sure you clamp off the line and release the bleed screw. If not you can destroy the ABS module.

I have seen this several times in the past.

The FSM doesn't call for this method when changing pads. It simple states to remove some brake fluid from the reservoir, and "mechanically" depress the caliper.
 
x2 If the FSM doesn't mention anything about destroying the ABS model I'm not worried and I wouldn't waste my time... Mr. T designed the car and Mr. T knows how to service it.
 
I use big channel locks.

I have c clamps, but it seems to go easier/faster with the pliers. :)

Love the giant channel locks, they make quick work of that big spring plate that holds the outer caliper together. I can't get them to squeeze the last bit when pinching the whole caliper and pads together when starting this job, always end up finishing with the c-clamp.
 
Of course, release the brake fluid pressure by opening the resevoir.
Another technique is to put two pieces of metal in between the calipers and then gently wedge a chisel between the metal plates and start pushing the chisel. The two metal parts could be the old brake pads.
 
Make sure you clamp off the line and release the bleed screw. If not you can destroy the ABS module.

A little paranoid perspective, but, along with the fact that the FSM does not call for this, I would NOT want to clamp off the line as it could cause casing cracks within the line. The easiest thing to do is just make sure you dont dump fluid from the reservoir by pushing back pads. I do like opening up the bleed screw but I do not like clamping off the line. Like I wrote, a paranoid perspective but ... :cheers:
 
Did you ever wonder???

Why does my brake fluid container look low and why do I see no leaks?

Well here is an easy explaination.
As your brake pads wear the volume of brake fluid required increases. Therefore before adding brake fluid to a non-leaking system make sure you check your brake pads for wear.

Now if you have been adding brake fluid before your brake job make sure you open the top and remove some fluid prior to squeezing the calipers otherwise when you squeeze the calipers the now excess brake fluid will be forced out.


As for stuck pistons: seperate the caliper from the disc and pads and now slowly apply brake pressure via the "C-clamp" and brake pedal. Once the piston begins to move you can spray WD40 or similar product and clean with assistance from your "C-clamp" , big pliers, wood and hammer or what ever else works.
 
Last edited:
before I start, I break the bleed nipple loose, tighten it back gently, and put a piece of 1/4", clear, tubing on it. The tubing stretches over the nipple and stays there nicely. The other end of the tube is in a small water bottle. I drilled out the bottle lid to fit the hose tightly, so the hose is held in all the way to the bottom of the bottle. I have a very small vent hole in the lid as well. When I'm ready to squeeze the piston in, I open the bleed valve, and a little fluid starts out. Then I squeeze, and the fluid flows nicely into the bottle. When I can't get any more flow, I'm probably bottoming the piston. I close the bleed, pop the tube off, put the bleed screw cover back on. Simple and clean.

After installing pads, I stomp several times on the brake pedal to fill the pistons and set them against the disks. Then I top off the brake reservoir.
 
I am super lazy,
I bouhgt a $15 speed bleeder from napa, basically it is scott's tuobe with a check vavle where he has his water bottle, makes it really easy to bleed the brakes as well, Like when I replaced the calipers this weekend. It was nice, 5 minutes with teh wife and lines completely cleaned out.
Dave
 
There is no difference in pad thickness between the different 80 series pads. Just a difference in materials and a response to a law suit. I personally like the last year of brake pads as they wear the longest(ie 97 model year). the early ones (93-94) are on the soft side of things and wear the fastest, but will not squeal as easy or hurt the rotor as easly. As for the last little bit, it some times takes a little more force to get the pucks to seat with older calipers. I usually use the old brake pad to push the pucks in. I use the pad surface against the rotor and the metal against the pucks. I turn the pad side ways to get more leverage. This works in 99% of the cases unless the caliper is screwed up. Just my experence. Good luck with your choices. Later robbie
 
Make sure you clamp off the line and release the bleed screw. If not you can destroy the ABS module.

Never heard of that, and regardless just loosening the bleeder will keep fluid from the ABS module. The ABS module on the 80 is passive, IOW it has no return ck valving. Some of the later ABS vehicles have master cylinder disk orifaces (to reduce ABS chatter) that can get compromised from backwash of bad fluid. That does not apply to the 80.

Loosening the bleeder screw only reduces the amount of fluid you need to flush. I normally just take the cap off and remove some fluid, then do a good full flush with a quart of Valvoline synthetic.

I have a lot of service tools for piston retraction. My most used is a 24in handle set of channel locks with a old factory pad. Pad service on an 80 is almost as quick as a porsche 993. I did all 4 sets of pads a few weeks ago with bleed, in under an hour.

HTH and my .02

ST
 
Back
Top Bottom