Body mounts

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 22, 2003
Threads
284
Messages
8,118
Location
Kansastitty
I really did search, really. I also read the directions with the kit, but I have a few questions.

Should I remove all of the old ones and then loosely bolt up the new ones until they are all in place then tighten?

Or can you just R&R one at a time? Like is there enough wiggle room?


The kit is Energy suspension I got from Kurt. Looks like a well made kit.


I already sprayed everything really well with PB Blaster. Nice cologne, BTW:)


Ed
 
If the body mounts haven't been removed previously to your replacment; I would think it would be easier to have them all loose and able to be removed before you install the new set. I think the two in front of the rear cross member would require you to remove or loosen the ones on both sides of it for replacement. I'm not sure if you even have those particular mounts as I did this on my '81.
 
AlaskanWheeler said:
If the body mounts haven't been removed previously to your replacment; I would think it would be easier to have them all loose and able to be removed before you install the new set. I think the two in front of the rear cross member would require you to remove or loosen the ones on both sides of it for replacement. I'm not sure if you even have those particular mounts as I did this on my '81.


Are you talking about the ones that have no bolts, just wire "keepers?" I see what you mean by your post.
Thanks for the help.:)

Ed
 
Degnol said:
I already sprayed everything really well with PB Blaster. Nice cologne, BTW:)


Ed

Just for future reference, Kroil smells, tastes and works quite a bit better.:D
 
IDave said:
Just for future reference, Kroil smells, tastes and works quite a bit better.:D

Have heard of Kroil, but never run across it....yet. I normally don't wear PB Blaster, just when on a creeper, spraying above my head;) BTW, it helps loosen my joints, too:D Funny that.

Kroil? Online thing or autoparts store?


Ed
 
hey ed,

when i replaced body mounts i loosened all than went around and replaced each one..starting at the front and working towards the back...i replaced the ones across the back last...then once they were all in i tightened em all down..not a hard project...one note..the mounts i bought from spector did not come with the new pads for the running boards..mine needed replaced so i had to order some new ones...good luck

marc
 
osagecruiser said:
hey ed,

when i replaced body mounts i loosened all than went around and replaced each one..starting at the front and working towards the back...i replaced the ones across the back last...then once they were all in i tightened em all down..not a hard project...one note..the mounts i bought from spector did not come with the new pads for the running boards..mine needed replaced so i had to order some new ones...good luck

marc


Thanks Marc, I'll go in that direction.:)

Ed
 
It's possible, unlikely but possible, to shift the tub on the frame if all mounts are loose at the same time. The tub isn't all that heavy, particularly when stripped out, and an inadvertent bump could cause a shift.

sometimes you might want to do that but usually when just changing the mounts you don't.

I like to loosen all on one side, change those, then do the same for the other side. The only ones I've ever had trouble with have been the three or five across the back and that was only because of the narrow space available.
 
honk said:
It's possible, unlikely but possible, to shift the tub on the frame if all mounts are loose at the same time. The tub isn't all that heavy, particularly when stripped out, and an inadvertent bump could cause a shift.

sometimes you might want to do that but usually when just changing the mounts you don't.

I like to loosen all on one side, change those, then do the same for the other side. The only ones I've ever had trouble with have been the three or five across the back and that was only because of the narrow space available.


Thanks, Honk. I'm going out there right now. To save time, I just sprayed PB directly in my face and ran my knuckles across the belt sander.;)

Ed
 
Degnol said:
Thanks, Honk. I'm going out there right now. To save time, I just sprayed PB directly in my face and ran my knuckles across the belt sander.;)

Ed

You're ready then.

Good thing you didn't get the PB blaster on the sanding belt. Might ruin it. :)
 
Got it done, with the help from the son-unit. I used the Energy Suspension kit I got from Kurt and I was impressed with the quality of it. The two front mount were a bitch because of the thickness of the plate with the nut attached vs the space I had to wedge it in. I can see the advantage of the "C" or "U" style mounts. This kit did include the mounts for the running boards.

I took your suggestion, Honk and did a side at a time. It worked well:)

Happy Father's Day....to me:D
bodymounts 001.webp
bodymounts 002.webp
bodymounts 003.webp
 
Those do look sweet!
 
Ed, you may well notice an improvement in your truck - a little tighter, a little quieter, a sense that the cruiser is more supple. Unsettling noises that you heard as rattles and bangs might now have become reassuring deep thumps.

or not.
 
honk said:
Ed, you may well notice an improvement in your truck - a little tighter, a little quieter, a sense that the cruiser is more supple. Unsettling noises that you heard as rattles and bangs might now have become reassuring deep thumps.

or not.


Well.....if the truck had an engine....or a transmission/transfercase.....I could take it for a spin and compare, but even if a couple of those unsettling noises (especially when twisted) would go away, I'd feel like I accomplished something. I know there are more than a couple of ways to skin a cat (that's a metaphor for all you cat lovers) doing it like you suggested worked out well for me:)

I'ma gettin' some Kroil. One of the bastids locked up on me, consuming a lot of the time devoted. SawZall, cutoff wheel, air chisel, and a few choice words.
If you look at the pic of the take-offs, some looked servicable and some were waaaaay crushed. Still not bad for 40 years:D

Thanks All!:bounce:

ed
 
You might want to loosen up the bolts that attach the plate that supports the steering column at the firewall and see if it wants to move to a new position to relieve any stress on the rag joint and then retighten.
 
Back
Top Bottom