Big work this weekend

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 8, 2018
Threads
7
Messages
36
Location
NY
Purchase my 97 FJ80 about a month ago. Ordered parts for new brake pads, rotors, caliber front and rear and need to replace Power Steering Pump.

If any one has any wise words of advice before the undertaking, I'll take it. I've done a bunch of reading on the forum and will be forever thankful for all of this great info!

Also order a Bosal exhaust to replace and of course thats a disaster with rusted stock mounts and bosal mounts not lining up.
 
If you don't know when the front knuckle job was done, you might as well add that to the party as well. Brakes: be prepared to bleed the heck out of them. Once you think you've properly bled them, do it again twice. Some people bleed the brakes, go out and try to engage ABS, then bleed again. I've never been able to get my ABS to engage on a test spin (no gravel or ice near my house normally). I used a vacuum bleeder last time with good results. I personally think nothing beats the 2-man pedal pump method :o

I would scrap the bosal exhaust and go to your local mom and pop muffler shop, personally :hillbilly:
 
If you don't know when the front knuckle job was done, you might as well add that to the party as well. Brakes, be prepared to bleed the heck out of them. Once you think you've properly bled them, do it again twice. Some people bleed the brakes, go out and try to engage ABS, then bleed again. I've never been able to get my ABS to engage on a test spin (no gravel or ice near my house normally).

I would scrap the bosal exhaust and go to your local mom and pop muffler shop, personally :hillbilly:

Regarding you comment on the exhaust....after my headaches and research, I couldnt agree more.
 
ninja edit ^
 
Not sure what your budget is but baselining is a hell of a drug.

I would look to rebuild as much as possible. PS pumped and calipers can be rebuilt. Its pennies compared to new and youre gonna need all the pennies you can get for wear items like bearings and gaskets and studs and bushings.

Super worth it, mind you. Myself, id be in the poor house if i bought it all new.
 
Purchase my 97 FJ80 about a month ago. Ordered parts for new brake pads, rotors, caliber front and rear and need to replace Power Steering Pump.

If any one has any wise words of advice before the undertaking, I'll take it. I've done a bunch of reading on the forum and will be forever thankful for all of this great info!

Also order a Bosal exhaust to replace and of course thats a disaster with rusted stock mounts and bosal mounts not lining up.

I'd bite off manageable chunks instead of tearing into all of these jobs at once.... if you are set on doing brakes focus there however leave the front rotors in place (if within tolerance) until you do the steering knuckle rebuild (if needed).

If the brake hoses are original plan on replacing those as well since the system will be opened up. When doing brake work I try to keep fluid in the system as much as possible so I would focus on one corner at a time, bleed it through, then open up the next side. I personally prefer the one man bleeder approach aka "gatorade bottle" method since it's easy, cheap and proven.
 
Decided to buy new PSS pump (not rebuild) and new calipers. I know that will outrage a lot of people who chose to rebuild, but, this will make my life a bit easier.
 
your going want to repack the front wheel bearings while the hubs are off, you have to remove the hub to replace the rotors. youll also want your drive flange gasket x2 and the rear hub seal x2, their the same part number for both sides so they can go on either side
 
Do gravity bleed , you can do this by yourself and not risk damaging your master cylinder by pushing to deep on the 2 person pump and dump. I would bleed the lspv. Also you’ll need to activate the abs or get rid of it. Rebuild the whole axle your already there
 
Do gravity bleed , you can do this by yourself and not risk damaging your master cylinder by pushing to deep on the 2 person pump and dump. I would bleed the lspv. Also you’ll need to activate the abs or get rid of it. Rebuild the whole axle your already there
 
From what I've read...sequence is LSPV, RR, LR, RF, LF
RR, LR, LSPV, RF, LF
However delete the LSPV with a union or a tee and the brakes will work much better.
 
Decided to buy new PSS pump (not rebuild) and new calipers. I know that will outrage a lot of people who chose to rebuild, but, this will make my life a bit easier.
Everyone should make their own life as easy as they feel it ought to be. Its your time vs. your money.
 
To comment on the Bosal cat back exhaust; I replaced my old leaky factory exhaust with this and couldn't be happier. The fit, welds, and flanges are well done and the exhaust note is stock sounding. I'm pleased with its. I did have to source my own hardware. 7/16" bolts, washers and nuts are needed.
 
Back
Top Bottom