Baslining Check List.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

So what line do I disconnect to avoid lying on my back to change the oil?

Right behind grill on LH side the top line that goes into Tranny Cooler. Some put a piece of hose and let it drain into bucket. Start motor and let it pump till it spits. Shut off and refill with same amount. You can recycle used oil in new oil container.
Mine pumped out about 4 qts or a gallon.
 
Right behind grill on LH side the top line that goes into Tranny Cooler. Some put a piece of hose and let it drain into bucket. Start motor and let it pump till it spits. Shut off and refill with same amount. You can recycle used oil in new oil container.
Mine pumped out about 4 qts or a gallon.


I was referring to motor oil.

It seems a little odd to think of not wanting to lie on your back for the transmission, but lying on your back for the engine oil. Maybe I'm thinking of it backwards because I don't just change oil while I'm down there, I'm sliding around to see if anything is broken, greasing u-joints, moly in the knuckles, gear oil in the diffs, etc.

Everyone is always so spun up about finding a way not to lie on their back, but how else do you check under your truck for other issues or service things? :meh:
 
Use a creeper and if you don't have a driveway use a large piece of cardboard to slide around on.
 
I don't mind working on my back ;) but I am curious about what people think about swapping the tranny fluid. I ran 5 gallons of some off-brand ATF through the A440F that I had in my 62 and I never had a problem with it for the 100,000 miles that I owned it for. I think it had 275,000 when I sold it. Is there any reason to use anything fancy or synthetic in this truck? I don't want to flush it, I will just drain and fill it a bunch of times over the course of a month or two.
 
I don't mind working on my back ;) but I am curious about what people think about swapping the tranny fluid. I ran 5 gallons of some off-brand ATF through the A440F that I had in my 62 and I never had a problem with it for the 100,000 miles that I owned it for. I think it had 275,000 when I sold it. Is there any reason to use anything fancy or synthetic in this truck? I don't want to flush it, I will just drain and fill it a bunch of times over the course of a month or two.
In my experience it depends on what the tranny fluid is like. If its badly burnt leave it alone, if it's only dirty or old then it should be ok to change the fluid
 
In my experience it depends on what the tranny fluid is like. If its badly burnt leave it alone, if it's only dirty or old then it should be ok to change the fluid

If it's badly burnt(mine isn't I smelled it, it smelled and looked fine) what do people do? I would think you would want to get that out of there. No?
 
I don't mind working on my back ;) but I am curious about what people think about swapping the tranny fluid. I ran 5 gallons of some off-brand ATF through the A440F that I had in my 62 and I never had a problem with it for the 100,000 miles that I owned it for. I think it had 275,000 when I sold it. Is there any reason to use anything fancy or synthetic in this truck? I don't want to flush it, I will just drain and fill it a bunch of times over the course of a month or two.

Synthetic in the motor let's you be lazy. Cheap Wally World crap (super tech?) in the trans, brakes, diffs, and knuckles let's you be more cost efficient so you can change them more often with fresher fluid that doesn't cost a small fortune.

I also use green grease in the u-joints and DTE24 in the power steering.

The whole "cost of owning an 80" thing is bull**** in my opinion. My tires cost quite a bit more than maintenance items have.

Then again, my "baselining" consisted of driving the truck six hours home from LA then became my daily driver, which it still is.

Sure, some things have needed to be fixed or replaced along the way, but that's normal for any 20 years-young vehicle. But checking the condition of things from time to time is probably a better approach than replacing everything and wondering where a problem is after throwing a ton of money at it.

The closest I've been to baseline is going to the Costco on Baseline Road for pizza with a couple other land cruiser owners. My avatar should help with that one.
 
No you leave it until the trans dies. Changing the fluid when its burnt leads to its almost immediate death. The clutch material is suspended in the fluid.
 
I put Chevron Delo 400 LE in all my 4 stroke engines. DEO is more heavily fortified with engine vitamins.
 
Synthetic in the motor let's you be lazy. Cheap Wally World crap (super tech?) in the trans, brakes, diffs, and knuckles let's you be more cost efficient so you can change them more often with fresher fluid that doesn't cost a small fortune.

I also use green grease in the u-joints and DTE24 in the power steering.

The whole "cost of owning an 80" thing is bull**** in my opinion. My tires cost quite a bit more than maintenance items have.

Then again, my "baselining" consisted of driving the truck six hours home from LA then became my daily driver, which it still is.

Sure, some things have needed to be fixed or replaced along the way, but that's normal for any 20 years-young vehicle. But checking the condition of things from time to time is probably a better approach than replacing everything and wondering where a problem is after throwing a ton of money at it.

The closest I've been to baseline is going to the Costco on Baseline Road for pizza with a couple other land cruiser owners. My avatar should help with that one.


I hear ya'. I am going to swap out all of the fluids because this truck is nice enough to keep for awhile and I kind of enjoy that type of stuff. The PHH is getting changed because I live in an area that gets down to -40F fairly regularly and there is a lot of remote driving to be done in the winter. I don't want to break down over a cheap piece of hose.

That said, I am not a believer in super fancy oils. AmsOil is headquartered in the city I live in, but that stuff is just too spendy for my blood and these trucks were manufactured before synthetic stuff became the norm. I still run dino in my trucks and I have yet to have one konk out due to engine failure. I just follow the manual and change it if it looks cruddy. The front axle is a different story because I don't think the people I am buying it from ever had it fully serviced in the 18 years they owned it and you can see that the inner seal is leaking. That's no biggie though and I don't need the truck as a daily driver. I have my Taco for that, heck I ride my bike to work everyday, so really, I could go without either of them for quite a while. I just want to keep the Cruiser as a bomber winter and camping rig to explore the great north woods with and hopefully keep it in good enough shape that it will eventually be worth more than what I paid for it.

I agree with you though on just randomly replacing things for the sake of replacing them. Part of what makes these trucks so appealing to me is that you can usually still drive them for quite some time before you HAVE to replace a part that you know is failing. Dumping all the coolant out at once doesn't fit that scenario though :doh:
 
Last edited:
No you leave it until the trans dies. Changing the fluid when its burnt leads to its almost immediate death. The clutch material is suspended in the fluid.
Today I learned. Thanks for that. Good to know. This will actually only be the third truck out of probably 20 that I have owned that has had an automatic. If it wasn't that beast that Toyota jammed under there, I would be very skeptical of an auto trans.
 
Do you use the 5W30? I like the pricing I am seeing on that stuff.
I run the 15w40. I also run it in my cummins. I have left it for as far as 13k miles and Black Stone labs told me to keep running it.
DEO is more robust and will clean the hell out of your engine. The additive package is larger than in oil for gassers.
 
I run the 15w40. I also run it in my cummins. I have left it for as far as 13k miles and Black Stone labs told me to keep running it.
DEO is more robust and will clean the hell out of your engine. The additive package is larger than in oil for gassers.
I am going to give it a whirl. I probably won't run it for that long, but it's good to know I can.
 
I am going to give it a whirl. I probably won't run it for that long, but it's good to know I can.
For enough oil info to choke King Kong, go to Bobistheoilguy.com. Tons of info there. What it boils down to is this, what's on sale and has your needed specs not to mention your favorite color bottle. I just happen to like blue and bought stock in chevron. :)
 
I just happen to like blue and bought stock in chevron. :)
Ahh, the truth finally comes out. I like the cut of your jib.

I will check that site out though. I lie awake at nights wondering things like whether or not the place I buy gas is topping off his tanks with a garden hose each night and whether my gear oils are where they should be. I have always kinda sided with the idea that it probably doesn't matter what you buy, at least not in the US, as long as you are changing it frequently. That said, I am fairly certain there is some sort of 22 year old fluid or grease in this truck and I think it's time for that that to be liberated.
 
I'm finishing all this baselining in the next few weeks. I decided I would do all PM before taking the truck out. Its been a grueling amount of work over several months. I had a few extras to take care of since I had to replace my rear axle housing but the rest was just PM. I'm a total novice but there's more than 100 hrs of work into this truck. It was fun but it was also hard.
 
I'm finishing all this baselining in the next few weeks. I decided I would do all PM before taking the truck out. Its been a grueling amount of work over several months. I had a few extras to take care of since I had to replace my rear axle housing but the rest was just PM. I'm a total novice but there's more than 100 hrs of work into this truck. It was fun but it was also hard.

Ha! Yeah, me too. I ended up doing the HG, front axle rebuild and a bunch of other stuff. Waiting to get the head back(their pressure tester broke and the guy had to rebuild it last night). I am hoping I can put it all back together this weekend, but if not, I decided that I am going to delete the ABS and the LSPV systems and replace the rear calipers and pads as long as I am waiting. At this point, there really won't be too many things to re-do, assuming nothing major breaks. I have no idea how much time I have into it, but I would guess north of 100 hours as well. All in all, I am still happy with the purchase, but I am glad I paid what I paid, rather than what the people I bought it from were initially asking.
 
I would change the EFI and circuit opening relay, and the fusible link as PM. And the heater control valve and PHH. Those are all things which could leave you stuck in BFE. While I have the usual MUD OCD, I think the usual list of PM stuff does not sufficiently prioritize things which could leave you stuck somewhere. So, I'd look at the amount of time and money you have at the beginning and move up the list things like fusible link (an $11 part which is known to fail) and perhaps wait on the PS fluid. Just my two cents.
 
I would change the EFI and circuit opening relay, and the fusible link as PM. And the heater control valve and PHH. Those are all things which could leave you stuck in BFE. While I have the usual MUD OCD, I think the usual list of PM stuff does not sufficiently prioritize things which could leave you stuck somewhere. So, I'd look at the amount of time and money you have at the beginning and move up the list things like fusible link (an $11 part which is known to fail) and perhaps wait on the PS fluid. Just my two cents.

I replaced the fusible links already. I am doing the PHH as part of the HG job and the heater control valve seems fine. What is the EFI and circuit opening relay do for me?
 
Back
Top Bottom