Baslining Check List.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

The EFI and COR are two small electrical relays which allow the fuel pump and fuel injection system to operate. The two parts are interchangeable, about the size of your thumb, and about $13 each. One is in the top L corner of the engine compartment fuse box, the other is in the DS left foot kickpanel, and takes about five minutes to get to.
 
The EFI and COR are two small electrical relays which allow the fuel pump and fuel injection system to operate. The two parts are interchangeable, about the size of your thumb, and about $13 each. One is in the top L corner of the engine compartment fuse box, the other is in the DS left foot kickpanel, and takes about five minutes to get to.

OK, I know where those are because I was rooting around in the fuse boxes trying to figure out what turned into a simple 10 amp fuse fix. So just replacing them is all you are recommending?
 
Yes, and there is a spot in the engine bay fuse box where you can store a spare (diagonally down and to the R of the EFI fuse). So, I'd replace both and put one spare in that slot in the engine bay fuse box and the other in your glove box/trail spares box. Same with your heater control valve. If the one you pull off is serviceable (it might disintegrate upon removal) keep it for yourself or a buddy.
 
Yes, and there is a spot in the engine bay fuse box where you can store a spare (diagonally down and to the R of the EFI fuse). So, I'd replace both and put one spare in that slot in the engine bay fuse box and the other in your glove box/trail spares box. Same with your heater control valve. If the one you pull off is serviceable (it might disintegrate upon removal) keep it for yourself or a buddy.

What goes wrong with the heater valve? I took mine off as part of the HG job and to bypass the rear heater lines, but it seems fine on the outside and the thing that moves the flapper inside seems to function. Am I missing something?
 
They just get old and brittle with heat cycles. Many replace them as PM because if it fails it can lead to overheating/HG failure, and strand you. I did it as PM. The part is about $60. You just have to weigh it out, whether it's worth it to you.
 
They just get old and brittle with heat cycles. Many replace them as PM because if it fails it can lead to overheating/HG failure, and strand you. I did it as PM. The part is about $60. You just have to weigh it out, whether it's worth it to you.

I will take a closer look at mine. I will probably just get a new one as now would be the time to do it as I have all of the coolant out anyway.

Thanks for the tip!
 
I decided to order a new heater valve. I think the old one was fine, but I just figured that if it wasn't I was going to blow $20 on new coolant if it sh!t the bed anyway, so I will toss a new one in as part of my HG and motor refresh job.
 
EFI relay p/n 90987-02004

@bicycleagent003 do you have p/n's for the other parts?
 
Sure, the heater control valve is 87240-60170, and the fuel pump relay is 28380-66010. My FP relay failed a few weeks ago at the edge of Sequoia National Park and cost me over $400 in towing and (unsuccessful) work at the local Toyota dealership.
Cheers,
Russell
 
The EFI and COR are two small electrical relays which allow the fuel pump and fuel injection system to operate. The two parts are interchangeable, about the size of your thumb, and about $13 each. One is in the top L corner of the engine compartment fuse box, the other is in the DS left foot kickpanel, and takes about five minutes to get to.



The one in the kick panel is the open/close circuit. If it fails it will cause the code 25/26 correct?
 
Back
Top Bottom