Baggin' It!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I'm listening... A guy that I employ is a airbag suspension guru. I will show him this info. I know he has used the guys at suicide doors with really good results. The product they build is very good quality. I wouldn't use 1/4" line, it's just too sloooooooooooooooooooow. Internal bump stop:). The shocks are going to be very important. I'd agree, lots of rebound control is important. The most important part of any airbag setup is a clean well thought install. We ran all of his 1/2" lines through the frame. Clearance for the airbags can be a problem. The setup my friend has is 3/4" lines & it's too fast.

I think Dakota digital makes a badass controller. http://www.dakotadigital.com/index....ategory_id=71/home_id=59/mode=prod/prd131.htm
 
I think your right on the 1/2" line. The 1/4" I have isnt DOT and the hose seems cheap to buy anywhere, Also saw an article in truckin on copper pipe but not sure how it would hold up offroad. I'll leave most in place for the accessory line. I may go with a 8GAL tank from these guys and just get the line, check valve, 2 cheap valves and controls for now until I decide on a system controller and try to tackle the front end issues.

Another controller option is the auto pilot. http://www.youtube.com/watch?v=c0bbh2plgaU

Airride looks like a good system but their controller is ugly.

One other promising option I want to call on. Airrock, another jeep system.
http://www.offroadonly.com/products/suspension/airock/


More shock options, seem to be expensive but most are rebuildable which may make it worth the expense.
KING
BILSTEIN 9100
FOX
None seem to be adjustable from the cab though. Most systems don't seem to mention any special shock or issues with ride with the lack of adjustable dampening.
131_0303_cvtk06_z.webp
 
Just wanted to clarify a few things: I think one of you guys is talking about replacing the air bags in the place of coil springs while the other one is simply wanting additional air bag on TOP of the coil springs, right?

If you're looking to run air bags in lieu of coil springs, then several variables come into play: height control vs pressure control, shocks (extremely important), valve body, air compressor CFM.

www.offroadonly.com (as mentioned before) has been the pioneer in the air suspension arena for Jeep TJs. He has figured out the complete feedback system using height sensors, pressure sensors, automatic limp home mode, auto height adjustment (semi active suspension), etc. He used to use pressure feedback but found the height feedback to be more effective. I guess pressure stayed the same while the volume changed? Can't recall exactly the issue he had. Having a York to run the air system is nice due to the faster recovery of the air tank as the bags are refilling.

This topic has been discussed before so a search will reveal further info.

The Land Rover air suspension is quite awesome as far as design goes. Their parts selection suck as well as durability. However, I do happen to have couple of their valve bodies and used to have bunch of the air bags if I ever decide to go this route. They use height sensors for feeback and a Thomas air comp to fill the bags for: 4Low, extended height, 4High, hwy vs city, Ingress/Egress, rear hatch or side doors opening, etc. Lots of movements take place as you can see!

I'll be curious to see what you folks come up with as this would solve some of our issues with lifts/caster/driveline angles/etc.

BTW, revalving the 7100s is about a ten min procedure per shock so don't let that scare you.

:cheers:
 
Just wanted to clarify a few things: I think one of you guys is talking about replacing the air bags in the place of coil springs while the other one is simply wanting additional air bag on TOP of the coil springs, right?

Right, I threw the airbag on top of coil springs as an option / alternative. It has certain definate advantages. The one disatvantage would not being able to drop it all the way down to the bumpstops for getting in and out. I wouldn't call it 'simply' by any stretch of the imagination.

The one that really throws people is the air-lift air-bags inside the coil. Now, that can be described as simply as there isn't much to do there other than order the parts and slide them in (you can find some for the front if you look at alternate aps, Sumotoy on here did that). That 'airbag suspsension' isn't really much of an airbag suspension as it is an airbag spring rate inhancement.

I'll be curious to see what you folks come up with as this would solve some of our issues with lifts/caster/driveline angles/etc.

yes, and no. You still need to bumpstop a certain amount to get tires to fit without rubbing, so if you run at a low enough adjusted height to have proper caster, you may have limited or no uptravel. You could however set the truck up at 3-4" over stock, w/ caster correction for that height, and 2" bumstop spacers, L-shocks or the equivalent, and then at the times you need 6" of lift - like for approach or departure angle, you could air up to that height.

BTW, revalving the 7100s is about a ten min procedure per shock so don't let that scare you.

:cheers:


I don't think it's so much the dificulity of revalving the 7100's, it's the ability to do it on the fly. Like when you're at 3" over stock, at 60 psi, have a certain shock damping, and then at 5" over stock at 80 psi - when the spring rate has changed, be able to adjust the shock damping to this new spring rate.
 
Hey all, I was behind on e-mail, and finally caught up to this reply from Universal air suspension - so if anyone is interested in that type of set-up, give Zack a call.

From: Universal Air Suspension <Uniairsuspension@aol.com>
Date: Thursday, October 11, 2007 7:15 PM
To: hvogt1@cox.net
Subject: RE: AIrbag over coil
Size: 4 KB



Heath,

We did it here. It was basically a pipe that was welded onto the frame and
then a slightly larger plate that went and bolted ontot he bottom of the bag
so that when the bag is aired up the pipe on the bottom of the bag slides
over the pipe on the frame. You can see it in the middle of the coil here
on the website

http://www.universalairsuspension.com/off-road/gallery.php?sid=38&cid=23

I can have my guy here make a pair of brackets for $200



Zack Ratcliff
Zack@UniversalAirSuspension.Com
800-864-2470 x 114
909-495-1350 Fax
http://www.UniversalAirSuspension.Com

-----Original Message-----
From: hvogt1@cox.net [hvogt1@cox.net]
Sent: Thursday, October 11, 2007 2:33 PM
To: Universal Air Suspension
Subject: RE: AIrbag over coil

Zack -

Do you have any contact information for the owner that fabbed the center
support? I'm very interested in using you aero sport bag in this manner.

Heath


---- Universal Air Suspension <Uniairsuspension@aol.com> wrote:
> Heath Vogt,
>
> That was a custom built application. That was using our aero sport
> bags on top of the coil with a fab. Center support to hold the bag and
> coil together.
>
>
>
> Zack Ratcliff
> Zack@UniversalAirSuspension.Com
> 800-864-2470 x 114
> 909-495-1350 Fax
> http://www.UniversalAirSuspension.Com
>
> -----Original Message-----
> From: hvogt1@cox.net [hvogt1@cox.net]
> Sent: Wednesday, October 10, 2007 12:50 PM
> To: uniairsuspension@aol.com
> Subject: AIrbag over coil
>
> Dear Sir,
>
> While looking at your site, I saw the pictures of the Jeep Rubicon
> Unlimited with your airbag suspension. I am most interested in the
> rear aplication with the air bag mounted over a traditional coil
> spring. I do not what to convert my 80 series land cruiser to
> coilovers, but I would like the advantage of running air bags on top
> of coil springs rather than air bags or coil springs alone.
>
> I could not find on your site where you offer this type of set-up.
> Can you please provide me with more information?
>
>
> --
> Heath Vogt
> BSME
> Six Sigma Black Belt
 
Heath,

Excellent inputs.

Where I was coming from regarding the driveline angles/caster/etc. was that if it was me, I'd setup the rig for hwy height. Another words, set up driveline and suspension geometry for a decent low height hwy vibe free, proper steering scenario. Which translates to most folks using OME 850/860 (or thereabouts) spring height, around 2.5" nominal over stock. This height is easy on just about everything, no caster issues and such.

For off roading, you can pump up the air bags over coils to what ever you want barring any rubbing issues. True, your caster angle and driveline angle will be shot but who cares! You're doing a whopping 4mph on low range so these factors shouldn't matter much.

Regarding the 7100 valving, I'd suspect that you're not going to be changing this much once you find the proper valving. I'm running 400/135 in the rear and 400/100 in the front and this may well be a good starting point for air bag/over coil suspension system.

Reality will dictate on how to accomodate the additional shorter air bag over a set of coil springs. Perhaps cut the tops off the coil springs? The dual spring rate while offroading may not be fun but tolerable by using a good set of shocks.

Agree with you on the air bags inside the rear coils for just additional load carrying capacity. In fact, I just ordered a set about two hours ago to help with our out of town extra gear and camper carrying loading.

I'd love to see what we can come up with in the air suspension arena, including the proper ECU, height sensors and OBA setup. While this lends itself to additional hardware and failure points, one could offset this by not having to purchase the usual DC driveshafts, pinion angle correction, steering, etc.

:cheers:
 
I think Fox shocks have adj remote res type of thing, not sure of the lengths though.
 
Heath,

Excellent inputs.

Where I was coming from regarding the driveline angles/caster/etc. was that if it was me, I'd setup the rig for hwy height. Another words, set up driveline and suspension geometry for a decent low height hwy vibe free, proper steering scenario. Which translates to most folks using OME 850/860 (or thereabouts) spring height, around 2.5" nominal over stock. This height is easy on just about everything, no caster issues and such.

So - at that height, what size tire are you going to run?


For off roading, you can pump up the air bags over coils to what ever you want barring any rubbing issues. True, your caster angle and driveline angle will be shot but who cares! You're doing a whopping 4mph on low range so these factors shouldn't matter much.

yep, that part I agree with

Regarding the 7100 valving, I'd suspect that you're not going to be changing this much once you find the proper valving. I'm running 400/135 in the rear and 400/100 in the front and this may well be a good starting point for air bag/over coil suspension system..

I think you're missing the point - when you pump up the airbags to be at a higher height, you've changed the spring rate. Or if you pump up the bags to account for the 600lbs of crap you put in the back for a long trip - you've changed the spring rate. For different spring rates, you want different damping characteristics. If you can adjust the air pressue in the bags from in the cab, you can adjust the spring rate from in the cab, and therefore it would be handy to also be able to adjust the damping from in the cab.

I change my settings when I'm on road and off with my XL's, my dad does it with his RS9000's when he tows. The only thing that makes it even more desirable with an airbag set-up is that you're mess'n with the spring rates when you're mess'n with the pressure.


Reality will dictate on how to accomodate the additional shorter air bag over a set of coil springs. Perhaps cut the tops off the coil springs? The dual spring rate while offroading may not be fun but tolerable by using a good set of shocks.

Dual rate springs while offroading is more than tolerable, it's desirable. That's why coil overs are built that way.
 
Wow, busy day at the office for air bags today!
I got a couple return calls today and yesterday from at offroadonly, Kevin 651-644-2323, after calling him a couple weeks ago. He sounds interested is getting something set up and it sounds like they are offering bags for the Land rovers now that will work possibly work with their Jeep mounts. Not sure if these are the OEM replacement bags or a reversible type bag though. Need to get some pictures of the upper and lower spring mounts and look at some Jeep setups before calling back to discuss. He also really stressed spring side clearance but didn't mention much about shock choices or issues yet.
Alia, hope your helper bags work for you. I've had a set for 6 years with no issues. You should rant on how great they work for you after you install them so I can sell mine easier when they come off. :D
I ended up mounting the control in the glove box and the pump on the frame rail driver side and it worked great for both bags being on the same air anyway!
To answer your first question I agree with Heath on the bag over but just too many things to consider when you throw in the short springs and have to throw in all the additional components. It will be enough of a challenge to get the full bag system to work without having to factor this in. It would probably work with the OEM springs if you cut holes in the floor of the cab and raised some sort of upper can holders to make room similar to the old 280Z cars. I like this idea but it's making my head spin thinking about it, I think full bag in the rear for now anyway.
I'm still on the fence for shocks. I really like the in cab control idea but no one seems to offer the dual dampening remotely that I can find. Ohlins have their CES system but it looks like only for OEM applications not the public. It seems like outside OEM adjustable dampening does not seem to be an issue though. Hopefully one of these guys listed above will follow Rancho's lead on the in cab adjusting. In cab = BIG$$$$$


I at some point want to go with a ~1" lift over factory height on highway and tow with all castor settings, panhards and stiff spring rates ideal here. This of course with 35's but 20" blings and TOYO MT's to look right. I really like the simple firestone Praxis design on the bottom of the spring and would think this would solve several shock issues as well as give you a higher spring rate at the lower height for towing and high speed cornering we tend to come across here occasionally in CO. They are on the list to call eventually. I did run the OME mediums on 315/75-16 MRT's with no issues for a while 6 years ago.
4" to 5" in town and offroad seems to be more than enough. As much as that drunk out of control castor problem tends to be a burden it shouldn’t be as bad at low speeds as Heath mentions. Maybe set the caster up for a 2" lift.
First step for me though is to get bags that will run within the parameters listed above but leave at the 4.5" to 5" lift I have for now. After that is accomplished and I get to the front then it's game on.

ANYONE HAVE REAR UPPER AND LOWER SPRING MOUNT PICTURES???????
 
Heath,

From personal experience, when the LR air bags are fully inflated during the "extended height" mode, the ride is very stiff and a little bouncy. I can bet that the Airock system behaves similarly. So, I guess you'd have to find a compromise with the shock valving for all situations and go with it. Perhaps the Fox shocks with the adj remote res is the answer? I don't know.

Just thinking out loud, not trying to be argumentative!
 
Back
Top Bottom