ANOTHER Caster question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 14, 2007
Threads
126
Messages
602
Location
Fargo, ND
Yes, I have searched, and searched, and searched. I'm finding mixed answers. I have new springs that lifted my 97 3- 3 1/4 inches up front, 2.5 in the rear. Hub to flare is 23 inches driver, 23.5 passenger side (both front). According to one of Landtank's posts (IIRC), I lose about 1.75 degrees of caster for each inch of lift. That would mean I need 5.25 degrees of correction to get back to where I was. Can that be correct? I was thinking Slee's blues would be the ticket, but they only correct 3 degrees. Do I need the plates? The steering is pretty "darty", and I do have a vibe at about 75 mph also. Thanks, Dan.
 
How about 3" drop brackets? They should work too, right? They would be much easier for me to install (I'm staying at a hotel for a while). I guess if their hanging down got to me, I could sell them after I get home and do the plates. As for the rear u joints or slip yoke, you think that's what's causing the vibe?
 
drop brackets will work but a couple of people have had issues with vibrations and the knowledge base on here is limited as far as troubleshooting them for problems.

I wouldn't discount getting a hand from a local forum member with this. Pizza and beer does wonders in that department. If you were close by I would definitely help you out as well as others.
 
Actually, you have helped me out :-) Thank you. Decisions decisions.
 
motel car park fitment aside, you could slot the rear hole and the front hole, fit 3 deg bushes, and be close to what you need, or fit castor plates.

If the steering arm hits on the control arms you can grind a little off, or remove the steering arms off the knucle and press them to get it to clear. [they are cast steel, they will bend]


Vibration will be front tail shaft, a spacer under gearbox x member may help short term, or even just greasing the tailshaft if it hasnt been done for a while. We always grease the tailshafts as part of a suspension lift, to make sure everyone ie happy in thier new home.
 
Well, I called Slee today, and was told that I really should have a caster sweep in order to know exactly what we're dealing with- makes sense. I got the caster sweep. I'm -2.2 left and - 2.5 right. So, I need about 5-6 degrees of correction to put me back into the 2-4+ range. Slee sells the 3 degree bushings (not nearly enough) or the plates that they say corrects for 4" (too much?). I am still considering the drop brackets too- largely for ease of installation and because I would think that they would HAVE to get me back to spec- I lifted it 3" and the brackets drop it 3". BTW- Slee- it would make more sense if you advertised your caster correction options in the same units of correction i.e. inches OR degrees. It's hard to know what to get when one corrects 3 degrees and the other is for a 4 inch lift. Any ideas or other options anyone?? Thanks, Dan.
 
There is one issue with this, and it is based on the assumption that you see 1.75 degrees of caster change with 1" of lift. This is based on a 2D picture from the side, as you lift the truck, the axle rotates forward, however if measured (on an alignment rack) it is not 1.75 degrees of caster change per inch of lift due to the fact that caster is not a simple 2D picture from the side when measured. Camber and some other aspects come in play was well. We have seen 1 degree of caster change per inch of lift when measured on an alignment rack.

If you plot the angle of change that the OME bushings or our blue bushings rotate the axle is is not 2 or 3 degrees, it is more like 3.4 degrees and 4.x degrees (Can't recall the exact amount). However when you install them and you measure pre and post the effective change is less.

What does this all mean, we have to compare apples with apples. You want 5.x degrees change based on the 1.75 degree / inch rule, but the caster specs of the bushings are 2 and 3 (as measured). Our caster plates when drawn up is around 8 degrees, but when measured about 5.5 degrees. Our arms are about 13 degrees as measured, but net about 7 degrees when measured.

Clear as mud yet?
 
Dan, using the formula I do for calculating for caster the 3" drop bracket would put you back where you were.

My truck is right where your's is and I needed a DC shaft and adj panhard bars to smooth everything out.

I suggest doing everything and especially if this is a DD and seeing a lot of highway.

Again, go to the club house corner and post up on one of the local clubs and ask for some help.
 
What does this all mean, we have to compare apples with apples. You want 5.x degrees change based on the 1.75 degree / inch rule, but the caster specs of the bushings are 2 and 3 (as measured). Our caster plates when drawn up is around 8 degrees, but when measured about 5.5 degrees. Our arms are about 13 degrees as measured, but net about 7 degrees when measured.

Clear as mud yet?

Wait, come again :confused: You see I've got this problem. I've been living with this Grr noise for almost 2 years and I wanna get rid of it and the drop brackets. Only happens during deceleration. This weekend did some gardening, basically dumped about 1200 lbs of top soils on my back yard. That is 40 lbs per bag, 2 round trips to home depot. 1st round trip: 12 bags (12 x 40 = 480 lbs). 2nd round trip 18 bags ( 18 x 40 = 720 lbs). On each trip, after loading all the bags (all bags were in the rear most cargo area) the truck was perfectly leveled and the drive was smooth with absolutely no noise. Long story short, what do I need? A friggin heavy rear bumper? more caster up front? I was thinking of two options:

1st option: 2" front spacer from metal tech and Slee arms.

2nd option: slee 4" coils with Slee arms.

And the invisible 3rd option is get the rear bumper then wait and see what happens :D.

BTW: How do I get a caster swip?

Please advise...
Please forgive me if this sounds like thread hijack :frown:
Thanks :)
 
I am planning on using MAF drop brackets for now on mine.. They easily unbolt and can be sold later when I fab up a three link.

For now it will likely be a MAF/OME 3FR2 lift and a pair of bags in the rear for towing that can also be crosslinked.. I might get the kit w/o shocks too and run something else... bilstien, fox, koni dont know...

There may be less ground clearance aft of the tire where the drop brackets are however with cats still installed and the rest of the oem exhaust on there there are other low points...

FWIW I think drop brackets are a good option as it is easier to get both sides closer to the same and the OEM arm bushings flex better...
 
First, let me say that I truly appreciate all replies/opinions on this. Christo Slee- I appreciate the fact that I can call your shop and get a sensible, honest reply that I will need to know my caster numbers to effectively deal with this instead of just trying to sell me something. That says a LOT about how you run your business and I like it. However, your post is VERY confusing, but the part I can dig out of there is this [You want 5.x degrees change based on the 1.75 degree / inch rule,] - this is incorrect- I want 5 degrees of change based on a CASTER SWEEP and what I need to get back to spec. Is there any other measurement that matters? Am I missing something (not trying to be a prick)? I'm certainly not an expert,, but it seems fairly straight forward- I need +5 or 6 degrees to get back to spec. Still wondering.....Thanks all, Dan.
(There is one issue with this, and it is based on the assumption that you see 1.75 degrees of caster change with 1" of lift. This is based on a 2D picture from the side, as you lift the truck, the axle rotates forward, however if measured (on an alignment rack) it is not 1.75 degrees of caster change per inch of lift due to the fact that caster is not a simple 2D picture from the side when measured. Camber and some other aspects come in play was well. We have seen 1 degree of caster change per inch of lift when measured on an alignment rack.

If you plot the angle of change that the OME bushings or our blue bushings rotate the axle is is not 2 or 3 degrees, it is more like 3.4 degrees and 4.x degrees (Can't recall the exact amount). However when you install them and you measure pre and post the effective change is less.

What does this all mean, we have to compare apples with apples. You want 5.x degrees change based on the 1.75 degree / inch rule, but the caster specs of the bushings are 2 and 3 (as measured). Our caster plates when drawn up is around 8 degrees, but when measured about 5.5 degrees. Our arms are about 13 degrees as measured, but net about 7 degrees when measured.

Clear as mud yet? )
 
Rick, thanks for everything. So, what do you have in the way of caster correction? Do you use plates, bushings, etc?? Thanks, Dan.
 
Wait, come again :confused: You see I've got this problem. I've been living with this Grr noise for almost 2 years and I wanna get rid of it and the drop brackets. Only happens during deceleration. This weekend did some gardening, basically dumped about 1200 lbs of top soils on my back yard. That is 40 lbs per bag, 2 round trips to home depot. 1st round trip: 12 bags (12 x 40 = 480 lbs). 2nd round trip 18 bags ( 18 x 40 = 720 lbs). On each trip, after loading all the bags (all bags were in the rear most cargo area) the truck was perfectly leveled and the drive was smooth with absolutely no noise. Long story short, what do I need? A friggin heavy rear bumper? more caster up front? I was thinking of two options:

1st option: 2" front spacer from metal tech and Slee arms.

2nd option: slee 4" coils with Slee arms.

And the invisible 3rd option is get the rear bumper then wait and see what happens :D.

BTW: How do I get a caster swip?

Please advise...
Please forgive me if this sounds like thread hijack :frown:
Thanks :)

Hey, Riad, go to an alignment shop and tell them you want a caster sweep. They don't need to adjust anything, just do the sweep and give you the numbers. That's the starting point. Best case scenario is if you truly want to get rid of the drop brackets, is to take them off before the caster sweep. Weave your way over to the alignment shop and get your caster sweep....that will give you the starting point to know how much correction you need. Then you can figure out if you need OME or SLEE bushings or Landtank plates or Slee plates or whatever. Get the appropriate solution and install it.

That's pretty much what I did. I had OME bushings and they weren't enough. So, I uninstalled them, put in Toyota OEM bushings, got the caster sweep, and then ordered Rick's plates piloted appropriately for my numbers. My caster is now sitting in the 2.5*- 3.5* range.
 
Rick, do you make plates that would work for me? If so, how much do you sell them for? Thanks, Dan.
 
Wait, come again :confused: You see I've got this problem. I've been living with this Grr noise for almost 2 years and I wanna get rid of it and the drop brackets. Only happens during deceleration. This weekend did some gardening, basically dumped about 1200 lbs of top soils on my back yard. That is 40 lbs per bag, 2 round trips to home depot. 1st round trip: 12 bags (12 x 40 = 480 lbs). 2nd round trip 18 bags ( 18 x 40 = 720 lbs). On each trip, after loading all the bags (all bags were in the rear most cargo area) the truck was perfectly leveled and the drive was smooth with absolutely no noise. Long story short, what do I need? A friggin heavy rear bumper? more caster up front? I was thinking of two options:

1st option: 2" front spacer from metal tech and Slee arms.

2nd option: slee 4" coils with Slee arms.

And the invisible 3rd option is get the rear bumper then wait and see what happens :D.

BTW: How do I get a caster swip?

Please advise...
Please forgive me if this sounds like thread hijack :frown:
Thanks :)

sounds like you need a DC shaft u[p front if you already don't have one.

What is your front hub/flare measurement and what drop brackets are on there?
 
sounds like you need a DC shaft u[p front if you already don't have one.

What is your front hub/flare measurement and what drop brackets are on there?

I've got DC shaft up front from Christo for that same reason(see my sig). Drop bracket is 3". After DC Shaft the Grrr noise was reduced significantly but did not completely go away. My guess is this noise is now coming from the rear. I Replaced the rear U-joints with new OEM joints a month ago. Didn't help much. I need to measure the hub to flare measurement and post back later. If I adjust my rear pinion by getting some upper adjustable control arms, would that make any difference?
 
Back
Top Bottom