Air cleaner / Dist. help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 12, 2015
Threads
95
Messages
3,456
Location
Bakersfield, Ca
I've been looking at a lot of engine bay pics and I have a question on the vac line running from the side of the air cleaner down to the distributor in the first pic. Is that correct?
Also on the second pic of the carb there's what looks like an open port to the right of the green connector/red wire. Should that be plumbed to something?
Cruiser is a 75 and I was told the engine was out of a 78.

1.webp


2.webp
 
there is a lot to look at in those 2 pics
1st pic hose to air cleaner should be connected to the distributor cap for venting the distributor. the vacumn advance pod should be plumbed to the carb
2nd pic, I think, the big tube should be hooked up to the charcoal cannister?
the valve cover breather is not attached, so you are sucking dirty air into the carb
front brake line looks kinked at the master
gas feed line doesn't look right
etc, etc. that was a quick glance
 
there is a lot to look at in those 2 pics
1st pic hose to air cleaner should be connected to the distributor cap for venting the distributor. the vacumn advance pod should be plumbed to the carb
2nd pic, I think, the big tube should be hooked up to the charcoal cannister?
the valve cover breather is not attached, so you are sucking dirty air into the carb
front brake line looks kinked at the master
gas feed line doesn't look right
etc, etc. that was a quick glance


the Dist. is Tooth Off Clock wise maybe or servery advanced ?


missing wire atop of carb ,

check fuel cut solenoid is hooked up
 
There is a lot or not going on there. Seems like they didn't hook up any vacuum lines or breathers. I would search on here and you can pull up the vacuum diagrams for that motor, and I would search for pictures of the engine bay to see where the rest of it goes.
 
Thanks.

I have the valve cover breather it's just not installed on that picture. Engine is somewhat de-smogged. It had a smog pump but didn't have a belt so it wasn't operating.
Ran good like that and I removed the air injection system with some corresponding hoses.
Now it's not wanting to idle without the choke so i'm starting to check things.

I'll check out some diagrams to see what i'm missing.
 
Last edited:
My '78 has the original emissions equipment. First photo is of the hose connection from air cleaner to distributor:
IMG_0624.webp

The distributor is electronic (78 was first year), and the hose connects to a fat nipple the pre 78 distributors did not have. Cap it.
In the next photo you can see the hose connected to the pipe on the carburetor:
IMG_0625.webp

It's the red hose, and connects to a steel tube that mounts on the firewall, around to the passenger side, then to a tee connection to the charcoal cannister. The small nipple on the air cleaner above the green connectors runs to one of the nipples on the thermostat housing, also not on the pre 78 housings.

If you have any other questions, ask away. I'm no expert, but I'm learning more every day, and I can take pitchers!
 
IMG_0607.webp
 
With no air rail, you could just cap the EGR inlet on the carb. That is a hard cap to find. I used some PCV hose, a couple of hose clamps, and a cap screw. It resides under that braided cover, and it would be a big vac leak, and a totally toasted original hose that has the worst of fuel vapor, and exhaust to contend with over time. The cap screw's head is the same diameter as the tube. I can help with part sizes. See below.

There is also an open barb on the top of the air horn, cap that, but it probably just vents the bowl, and is not a vac leak.

GEDC1593.webp


GEDC1592.webp


My guess was that you removed the carb to get to the air rail? What was disassembled during the procedure?

However, being that @TheHardWay has the image of the '78 USA year motor, and your '75 harness only needs to supply power to the black (idle solenoid) part on the carb, you need to make sure that your red wire supplies power to the black wire, and not the green, if I am reading the wiring diagram correctly, and the images of your motor above.
 
Dizzy, what's the brass screw in sensor with the male electrical plug in the second photo for? I removed it before I soaked the carb in Berrymans, cleaned it and screwed it back in when I rebuilt my carb, but the FSM didn't show it in the carb diagram.
 
Also bolt your air cleaner body to the head. All the weight and vibration is being transferred to the carb bolt and can shake and tear up your carb and gaskets.
 
With no air rail, you could just cap the EGR inlet on the carb. That is a hard cap to find. I used some PCV hose, a couple of hose clamps, and a cap screw. It resides under that braided cover, and it would be a big vac leak, and a totally toasted original hose that has the worst of fuel vapor, and exhaust to contend with over time. The cap screw's head is the same diameter as the tube. I can help with part sizes. See below.

There is also an open barb on the top of the air horn, cap that, but it probably just vents the bowl, and is not a vac leak.

View attachment 2160115

View attachment 2160116

My guess was that you removed the carb to get to the air rail? What was disassembled during the procedure?

However, being that @TheHardWay has the image of the '78 USA year motor, and your '75 harness only needs to supply power to the black (idle solenoid) part on the carb, you need to make sure that your red wire supplies power to the black wire, and not the green, if I am reading the wiring diagram correctly, and the images of your motor above.

Thanks for the information. Carb was not taken off to get the air rail. I was able to get to everything pretty easily.

I'll check out the egr port you mention that's a good way to plug it I could piece that together.

Air cleaner body is bolted to the head just not in those pics as I just put it back
 
I was listening for the idle solenoid click with key turned on and Wasn't getting it. Started looking and the 15a engine fuse was blown which from searching is ran through that fuse.

Fuse block was pretty crusty and that port wad basically all broken so I ordered another one. Can't test until that gets here
 
I was listening for the idle solenoid click with key turned on and Wasn't getting it. Started looking and the 15a engine fuse was blown which from searching is ran through that fuse.

Fuse block was pretty crusty and that port wad basically all broken so I ordered another one. Can't test until that gets here


i offer both single and dual wire fuel cut solenoids if u need one ?

i also have heavy duty fuse blocks too ........
 
You can run a jumper wire (preferably with an inline fuse close to the battery) from the positive terminal to the solenoid to check the mechanical operation of the solenoid with the choke all the way open until your fuse block arrives?

I'm pretty sure that you're seeing an M10 x 1.5 socket cap screw (with a head diameter of about 16mm) in the photo above, for my EGR plug. I found a section of Armor Mark PCV hose identified as 9/16" / 15mm at O'Reilley to create the vacuum-tight seal. The measurement of a '75 EGR inlet tube (not at the barb) is about 16.05 mm OD; only the threaded part of the cap screw goes into the EGR tube.
 
:bounce: :bounce2:
 
Back
Top Bottom