? about 700r4's

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 8, 2004
Threads
16
Messages
54
Location
Detroit, USA
Hello,

New to cruisers and looking for options for my 75 FJ40 and have decided on using an auto trans (700r4). It already had a SBC 350 in it when I bought it. I plan to drive my cruiser a lot on the highway but take it moderate 4-wheeling (some dunes and 2-track trails, tank trails etc). I have searched and read a lot of posts and have found some answers but need more. I am learning about transmissions as I go and need a little help. Couple of questions....

What is the main difference between the 2WD and 4WD th700r4's...would i need the 4wd?
Are there any differences between the 700r4's used for v6's vs. v-8's...would I need the v-8?
Are there different year transmissions with different torque convertors in the 700r's and would one be better than another to try and find?
Are there certain number of splines to look for?

I plan to use the AA for 700r4 to my 4 speed toyota t-case.


I am looking for 700's and I can get:

86' chevy van - $100
88' Iroc camaro -$75
92' chevy 4x4 - $50
86'-88' trans am (both for) $75
89' chevy suburban plus 5.7L engine - $250
88' chevy 2wd truck 30 spline $80

TIA
 
get the one from the burb w/ the engine .Is your truck injected? Make sure you get the harness and ecm if you can . Get it rebuilt and make sure you get the tcc lockup kit. AA will give you a new output shaft for the tranny so make sure you get the kit before you send the tranny to the rebuilder .
 
thanks for the reply....anyone else have any comments or answers to my other questions asked?

thanks
 
yeah for every person that I have heard say they are junk I have heard another say the opposite......guess it is preference and type of stress placed on the trans.

Forgot to answer to too tall....no my 350 is NOT injected. I take it you recommend getting the harness and ecm since it is a 4l60e or 80e? So if I don't want the electronic and want to go with the 4l60 than I would not need the harness and ecm, correct?
 
if you're your 350 is carbed, then the electronics to control the 4L60e or 80e will cost you more than tossing the whole kit and buying a complete TBI/tranny together....

when RVBtruck gets back online, he'll have LOTS of good advice...he just went thru this exact scenario with a local FJ40 guy and they got it straight.

I have thoroughly abused the 700R in my FJ40 behind the TBI motor...it works great.

Might want to PM RVBtruck to check this thread - he'll likely be back online Tues after the holiday weekend (home with the flu now, sissy)
 
Many of the club members here are using 700r4s for their low 1st and overdrive. They run them with 350s or 383s and tires from 36 up to 44s, with driving styles from finesse to heavy right foot. Seem to have no problems with them across the board.
 
The early 700Rs had problems. Redesign and uopgrade in 1987 addressed that. If you are running a carbed motor, stick with the 700R, not the 460lE. No need for the complication of electronics

Pretty sure you can use either the 2wd or 4wd variant with the AA kit to mate to the Cruiser T/C. Pretty sure that the kit replaces the output shaft too. (I'm not at work and don't have all my AA info to look at, this is from memor.)

The 90* bellhousing pattern of the V8 and 4.3 V6 lets thm use the same tranny. The 3.8 V6 (and others) used a different pattern and the tranny from behind that engine wil not mate to a V8.

Mark...
 
thanks for the replies.....starting to figure stuff out. So, I know I definetly want the 700r4 and not the 4L60 or 80e. I was also told by a local tranny guy that I want the HD case which has a "K" marked on the outside of it....don't know if this is correct. He also said they have 6 bolts and have the 4/3 or 5/7 bellhousing pattern.

As posted above I have some options of trannys to buy cheap and am trying to figure out which ones I could use. I found the one out of the 89 suburban with the 5.7 litre that was 4wd but don't know if it was a HD case. Also found one out of a 92' chevy Z71 4WD but am assuming this might be an electronic one (4l60 or 80e) which I wouldn't want because of the needed wiring harness and ecm, correct?. Were there 700r4's that came out of Z71's that weren't electronic?

TIA
 
I think Chevy trucks ran TBIs into the early 90s with the 700R4

The later transes, post 89 I believe, are plenty strong and a good rebuilder can make it very strong. The problems have been addressed.

Advance Adapters has the info on 4wd vs 2wd. Good time to go to a split case. It's not worth spending the cash and then deciding to go to the better case later.

The 4.3 and 5.7 use the same bell housing.
 
So the Z71 and the suburban would probably be okay to use? I was thinking the Z71 would tend to be the HD case since it is marketed as more of an offroad package but don't know.
 
Yeah I guess it is a little confusing since the 700r4's are interchanged with the name 4L60's (although not many people use that name). From what I have read, early units 83-86 are technically called 700r4's and 89'-early93' (which are the ones to use and have K-cases) are called 4L60's. SO I guess I am already looking for a 4L60 which is better known as a kind of 700r4, I guess. Seems to me everyone knows what I am talking about when I say 700r4 versus 4L60 so I just go with what they know as long as I know that is is between those certain years, 4wd, K-case, etc.
 
Oh yeah and I DO mean 4L60 NOT 4L60e
 
LCP,

So that 92' Z71 tranny I am looking at "should" be one of the 4L60's with the different pan design that will clear the front drive shaft. Is it simply a different shape tranny pan with the same bolt mount pattern? Could you simply use a 90-92 4L60 tranny pan with a 700r 89 and up?
 
LCP,

So that 92' Z71 tranny I am looking at "should" be one of the 4L60's with the different pan design that will clear the front drive shaft. Is it simply a different shape tranny pan with the same bolt mount pattern? Could you simply use a 90-92 4L60 tranny pan with a 700r 89 and up?

I had to clip the corner on my 4L60 pan but I dont have a lot of lift. The pan and bolts are different on the two. I dont know of a 89-up 700r but I could be wrong.
 
I believe 700R4 was used until 1992. 1993 was the first year of 4l60E. Avoid the one made in the late 80's.

A 4 wheel drive 700R4/4l60E will have more clearance for clocking up a transfer case than a 2 wheel drive.
 
Back
Top Bottom