? about 700r4's

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

FJ40Charles,

Why not use late 80's? I have heard anything between 89-92 is solid. I don't want the 4l60e since I don't want to get into having to find a wiring harness and ecm.
 
probably going with the 92' Z71 though, providing it isn't a 4L60e
 
i am working on the same swap and trying to decide if i should use my stock transfer case. i now have an sm465 mated to 78 t-case. i picked up a complete '90 4x4 suburban 350 tbi, 700r4. is there a low gear kit available for the 700? I have heard there is. right now my first gear is 57:1 i think and the 700 would put it around 35:1. i'm considering the orion rather than paying for the adapter. any input would be appreciated
 
Never heard of a lower first gear for a 700r. 99% sure there is not anything like this available. But keep in mind the way an auto works. For real world use of the rig, you can consider that crawl ratio roughly double when comparing an auto to an manual.


Mark...
 
FJ40Charles,

Why not use late 80's? I have heard anything between 89-92 is solid. I don't want the 4l60e since I don't want to get into having to find a wiring harness and ecm.

I think 89 to 92 were good years. I would avoid anything before these years if possible unless you want to spend lots of money to rebuild. The drums on 700R4/4L60/E are weak. They separate from the shaft. You can get aftermarket drums for these transmissions.

My tranny guy says the best 4L60E is the one from a 95... Don't know why, but he rebuilds these things so he should know.

Also, I would try to get a "K" case. These are heavy duty cases from 4 wheel drive application. Not all 4WD drive cases are K cases. The cases have a big letter K on the bellhousing. The metal is thicker on these cases.
 
Alright here's the straight and easy skinny on 700r4's


1. The K case's only attribute is that it has the bosses to mount the cast aluminum cover for the torque converter. That's it, period, so all the hype about the "K" case is meh. We could argue the "structural integrity" difference but guys are running 6.0 atlases on the guys using the 2wd cases. It's all in the mounting.

2. 2wd and 4wd are easliy converted back and forth between 700r4s the 4L60E, however, is a different case.

3. With a carbed motor the best years to get are pre-87. There are modifications that can be made so there is no need to run electronics all together and still have lockup apply.

4. With a fuel injected or when pre-87 aren't available, any units that are pre-92 are good but will need to run the lockup or suffer the consequences. The unit WILL fail with out lockup. The lockup circuit applies lube to the back of the tranny. There are many different ways to set this up so when ready to do it ask, I'll help you set up the easiest for the application/use you have.

5. The pre-87 unit may come with a input shaft, 27 spline, that is NOT to be used. Very easy to replace with the new, 30 spline, unit when you have the unit checked over/output shaft changed.

6. All GM bell housings are the same for anything over 4.3L engines. This applies to rear drive up to 99-2000 (until full belhousing start to be used).

Pretty good primmer on what you need to know to find your 700. When it comes to setting up your 700 is another thread altogether.
 
Last edited:
One of my friends put a vortec 350 and 700r4 in front of a 3 speed case on his '73 FJ40-used the Downey adapter. Had the tranny rebuilt by bowtie overdrive...blew something in the pump a week after putting the tranny in(back to Bowtie). Put 35's on the car, and snapped the input shaft when the car bounced very slightly while trying to race somebody on the street(back to Downey-hey no warrantee!). A year later his torque converter started to slip and the tranny was shifting different-but he always drove it hard and never opted to use 4low since he didn't have a shifter and his right foot could usually blast him out of anything(probably would have helped the torque conv. using 4-low)
 
I used the AA Marks Adapter and a truck 4WD 700R4 and had to swap the shaft. As I am not into autos had to pay Trans shop $200 to make the swap.
 
Back
Top Bottom