AA rear T case bracket, Frame L bracket direction??

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 29, 2003
Threads
100
Messages
3,342
Location
Northern Minnesota
Question for you guys with AA's rear T case mount.

What direction are you welding in the L bracket on the frame. I see in there instructions they have the L portion up, but in 1 of there pics I see they have the L portion down.

Just wondering how you installed it, like my pic or the other way?

Thanks, Matt
tcase.webp
 
It depends on several factors. The centerline of the engine/tranny/transfer should have the same "slope" as the rear differential, within a degree or two, to avoid excess vibration, unless you plan on using a CV on the rear driveshaft.

Factors: how much lift; what type driveline; where will the motor mounts end up; vertical position relative to the frame rails; clearance for the floor pan; some others that I'm forgetting (fore/aft position); . . .

I hung mine in place with a cherry picker for a couple of days and tried to cover the bases, then made some marks and welded the brackets and mounts in. Didn't even think about up or down on the angle brackets you're asking about. Had to put them on in the only way that worked.

Hope this helps some.
 
I've heard some are happy with this bracket and others are not, what is the problem?

Thanks, Matt
 
I know one problem is a tendancy to leak. I used silicone sealer on mine two years ago and don't have problems, but I haven't wheeled it hard.

Also, it's a relatively rigid rear mount that doesn't flex like motor mounts do. So maybe engine torque tends to wear it out?
 
front of motor supported and rear of driveline supported means everything in the middle flexes and bounces and within a few months loosens and leaks. toyota cases are made to hang, not be hung.
 
My brackets are opposite of what you did..

My bracket leaked until I removed it and used Permatex..right stuff.
I also double nutted the studs in the bcak of the case. Nice to see you used studs... IMO studs with a shoulder for the bracket to rest on eliminates some slop and stronger than bolts.
 
Another question, just want to make sure I have my mounts right.

I have the thicker donut on the top of the bracket, looks right?

Thanks, Matt
tcase mounts.webp
 
buckroseau said:
Another question, just want to make sure I have my mounts right.

I have the thicker donut on the top of the bracket, looks right?

Thanks, Matt

Like others have said, mock it up in the vehicle and you will probably see that you don't have as many choises as you think because you have to deal with:
- Driveline angles
- Tub clearance
- Stock tube cross-member clearance (unless already removed or relocated.

You can waste a lot of time assembling it on the bench and still not know for sure what issues you will be dealing with until you begin to mount it in the chassis. TAKE THE NEXT STEP. Then share some pics. :D
 
miker said:
Like others have said, mock it up in the vehicle and you will probably see that you don't have as many choises as you think because you have to deal with:
- Driveline angles
- Tub clearance
- Stock tube cross-member clearance (unless already removed or relocated.

You can waste a lot of time assembling it on the bench and still not know for sure what issues you will be dealing with until you begin to mount it in the chassis. TAKE THE NEXT STEP. Then share some pics. :D

I haven't removed the tube cross-member yet, but it will be once the body comes up. THE NEXT STEP is scheduled for this weekend, starting Friday night. Goal is to come out Sunday with all mounts welded in, saginaw plates and frame stripped down ready for sand blasting.

Just making sure I have all my ducks in a row. :)

Pic of what it's going in this weekend.

Thanks, Matt
mud18.webp
 
miker said:
Very Cool!


BTW, I sent pm about valve covers.

Thanks, should be a fun project. I started a build up thread in the NEW 45 section if you want to take a look.

https://forum.ih8mud.com/showthread.php?t=39575

I got your PM, just debating whether I need them. In the pics on the thread you can see the 350 I'm building. I have steel chrome covers now, but they seem kinda cheap and I think there going to leak?

I will let you know, but I'm leaning that way. :)

Thanks, Matt
 
A: orientation of "L" can be application specific. dont sweat it, as it might only work one way.
B: I would put the "thicker" of the two rubber isolators in the order that places it in a compression load with the wieght of the drivetrain resting on it.(IE the way you have it now, with the thicker isolator above the frame L, and below the crossmember)
C: Propellor style rear mounts have proved troublesome. Just a fact of life that flex and a fixed four point mounting setup are going to have inherent issues. since the four points on the frame would not remain in the same plane if the frame twists(which it can and will even under normal driving etc.) yet the engine/tranny mounts want to remain in the same plane. the resulting difference in locations of mounting points is absorbed by some extent by the bushings, but also there is some twisting preload applied to the drivetrain and it shows up in two places. The interface between the t-case and the propellor style mount, and the interface between the 700r4 and the adapter and spacer. I have seen numerous adapters so loose you can see the t-case/adapter flopping around off the back of the tranny.
 
I made my own bracket, inspired by both t-case savers that are sold on the us market.

sadtlersbracket11ig.jpg


You will need srews that are 5mm longer than original.
On the right side it can be connected to the frame with a forked link and one of those rubbers you call donuts.

I am not selling that and if u want to build one like that, just do it. ;)
 
miker said:
Like others have said, mock it up in the vehicle and you will probably see that you don't have as many choises as you think because you have to deal with:
- Driveline angles
- Tub clearance
- Stock tube cross-member clearance (unless already removed or relocated.

You can waste a lot of time assembling it on the bench and still not know for sure what issues you will be dealing with until you begin to mount it in the chassis. TAKE THE NEXT STEP. Then share some pics. :D

So true Mike, so true. Shoehorn the biatch in there and it will tell you what it needs.
 
Interesting, but can't see it...

FJ40-GARAGE said:
I made my own bracket, inspired by both t-case savers that are sold on the us market.

You will need srews that are 5mm longer than original.
On the right side it can be connected to the frame with a forked link and one of those rubbers you call donuts.

I am not selling that and if u want to build one like that, just do it. ;)


I not seeing how this eliminates the problem of frame twist loosening the drivetrain bolts if you are still attaching your bracket to the frame. In fact, it looks like your bracket would provide less flex between the frame and drivetrain. If this is the case, if the frame twists, the drivetrain will be forced to twist too.

I must be missing something....
 
Back
Top Bottom