'67 Brake Master replacement

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

ace10

Another one bites the dust!
SILVER Star
Joined
Jun 24, 2004
Threads
80
Messages
2,359
Location
Rural NoVA
Looking for ideas on how to wrap up this little project.

Master cylinder went out on my '67. Purchased a new OEM one, but ran into the problem of incompatibility of threads on the existing hard line.

Been searching the forum, but couldn't find an actual resolution. Usually I can find what I need without resorting to a new thread. Ugg.


Old Master was threaded for M10X1.0
New Master is M9x1.0

Hard lines are in great shape, so I don't want to tear out anything unnecessarily.


Does anybody make an adapter for this? If there is, is that a good/bad idea? Any helpful suggestions are welcome....

20210614_133636.webp
20210614_133625.webp
 
Early FJ40s used the M9x1.0 fittings. If your hard line is M10, I would probably just buy a master cylinder that would fit and return/sell the one you purchased.

I could not find an adapter when I changed my brakes to disc so I ended up changing out everything to M10 including a dual master cylinder.

This master cylinder from cruiser corps will bolt up and will use the M10 fitting. You will have to reuse your factory rod though.

 
You should really think about a safety upgrade to a dual circuit master. You do share the road with others.
Dyno
 
Is there a source for the proper M9x1.0 fitting?

I could just cut off the flare and go from there....
 
If the hardlines are now 10mm lines, someone has replaced your lines or at a minimum replaced that fitting. What size are the fittings on the other end of that line? Is there an adapter on the other ends, or at any of the other connections? If they're all 10mm, someone has probably replaced the lines and components in your braking system.

As Dynosoar mentioned, you should consider upgrading to a dual master for safety sake. Currently, if 1 item in your brake system fails you will not have any brakes.
 
If the hardlines are now 10mm lines, someone has replaced your lines or at a minimum replaced that fitting. What size are the fittings on the other end of that line? Is there an adapter on the other ends, or at any of the other connections? If they're all 10mm, someone has probably replaced the lines and components in your braking system.

As Dynosoar mentioned, you should consider upgrading to a dual master for safety sake. Currently, if 1 item in your brake system fails you will not have any brakes.
McMaster-Carr has always been a good source for adapters and fittings. You might want to give them a shout. I've found that their customer service folks are very friendly and knowledgeable. Good luck!
 
Existing lines are 3/16" tube. The other fittings take a 10mm wrench, so they must be M9 thread. The fitting at the Master takes an 11mm wrench with M10 thread.


20210618_135944.jpg
 
The other fittings take a 10mm wrench, so they must be M9 thread.

Not necessarily. JIS M10 brake line fittings use a 10mm hex.
 
Not necessarily. JIS M10 brake line fittings use a 10mm hex.

In this case, you can see the threads step down off the wrench flats in the picture I posted.
 

This should work for you....


Thank you very much. Had to order a handful of them to make their $10 minimum.

If anyone happens along this thread down the road, and you find yourself needing this fitting, send me a PM. I'm sure to have extras.
 
This 40 doesn't get driven more than 2 or 3X per year. She's a rust free survivor and lives in climate control comfort out in the country.

In ten or twenty years when she goes to her next caretaker, they can decide whether to make changes to her original equipment. Axle conversion, roll bar, seatbelts, brake circuit... whatever. But for now she's staying as original as is reasonable and possible.

Thanks for the replies.
 
Back
Top Bottom