3B diesel glow plug problems

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 28, 2018
Threads
12
Messages
94
Location
United Kingdom
Has anyone any clues on how the timer pre heater on my 1982 bj42 works? My glow plug light has decided to stop working. The engine now starts reluctantly and runs rough for a minute then OK. I have a 2 relay system but why 2 ? No. 2 has a resistor on its 24 volt output. Why? Should I be able to read 24 volts at the glow plugs and for how long? Any explanations would be gratefully received before I go completely round the bend.
 
Are you sure they both are relays? I believe box number 2 is your glow controller, which would explain the voltage divider circuit. Can you measure any voltage at all at your plugs?

Check out this thread:
Which plugs should I be running - B, 2B, 3B, H and 2H diesels

If you’re interested I can provide the relay part number and wiring I used to build a manual glow circuit for mine.
 
The 2nd stage of the glow system is at a lower voltage. Its not as hot and helps the truck idle more smoothly at the beginning. The glow light isn't on while that stage is on.
 
I would certainly appreciate your part no. and wiring John. Just to be sure it wasn't my batteries (which needed renewing anyway), I bought 2 new today (ouch!). On ign. switch to ON, top of relay 2 resistor read 24 volts and bottom read 7 volts and rising up to 10. After about 10+ seconds both volts go to zero. I then checked volts at glow plugs on switching to START . She started OK but not immediately as previously. Glow plugs read 7 volts and rising to 10 then disappeared after 10 + seconds. Is that normal? The glow plug still does not come on at all unlike previously. I am showing what I think is my circuitry, but my timer pre heater wiring has 9 wires going into a 9 pin plug , unlike the drawings which show a 13 pin plug. ( makes fault finding difficult)

edic diagrams 076.webp


edic diagrams 077.webp


edic diagrams 084.webp


edic diagrams 085.webp
 
You have the 24v super glow system. I had mine for years and loved it. One relay is for the 3 second super glow where they hit the plugs with 24v and then the second relay kicks in for a longer smoothing glow of 12v. The intention is that your glow light comes on when the first relay is on. when that turns off you can start the truck. The second glow smooths out the engine for about another 10 to 30 seconds depending on ambient temperature (read via the resistance on the plugs)

You should be running 14v plugs. Also, just to make sure, do you have any taps off if the low side battery for 12v? If so, that will kill your batteries and wreak havoc on the 24v system...
 
Last edited:
Thanks SS. Your'e right it being a super glow system. I had unusual difficulty in starting the beast and only had success by pouring fuel into the inlet. Checking volts at the timer pre heater showed zero on all pins. Removed and scrutinised, as it is damaged, but no visible reason why it shouldn't function. Plugged it back in and 24 volts appeared on almost all pins. She still refused to fire up so, in desperation I removed the glow plugs. I now have 10mm of glow plug sitting on piston 3. I applied 24 volts to all glow plugs but no suggestion of heating up. Is that normal? My one concern has been that, with all the testing I have carried out, I inadvertently left the ignition key on START for several hours. Would that see off the glow plugs? Also , if I remove the fuel injector on piston 3 is the hole large enough to insert a magnetic probe?

edic diagrams 089.webp
 
Tell me more about fuel into an inlet? Where did you pour?

On the plug issue, it's fairly common for the plugs to go bad if one is bad... Bad Apple spoils the bunch. When that one failed, the rest are probably burnt out.

Not sure on the access from the injector side, but these have precups so the access into the cylinder in not direct in any means...
 
I removed the air filter and poured an eggcup of diesel direct into the air inlet. How it started with dud glow plugs I'll never know. My main concern now is that bit of missing glow plug. My removed g. plugs are NGK 9892 (not in Lostmarbles amazing research list). What are you using?
 
I also have superglow and changed mine to NGK 2188 Y-197R a few years ago. My truck would always start without the glow plugs functioning properly.. it would just smoke a little until it warmed up. That was down to about -10 Celsius so I somehow don’t think your glowplug problem would stop your engine from starting at all?
 
You should never put fuel into the air inlet of a diesel... Diesels can grenade if fuel is introduced into the cycle at the wrong time. While I am sure your plugs were possibly burned out before you added the fuel, the one that is gone could be from an improper detonation from the introduced fuel.

For next steps, I would definitely scope all four cylinders to make sure your pistons and walls look okay, I would also try to locate the broken off end of the nuked plug and try to pull it out with a small magnet on the end of a wire...

Did the truck just stop starting, or is this due to colder weather? When you started it the other day, (with the fuel) did you drive it or just start and shut down? If you drove it, how did the engine behave?
 
Having not being used for about 5-6 years she remarkably started up almost immediately. The only visible problem was the ignition light remained on all the time. This led me to the alternator which I eventually discovered only required an internal clean up. In the process of investigating the alternator problem, I can only think I introduced a problem in the heater timer unit because the glow lamp just decided not to function. I can't locate it's earth return as the lamp correctly reads 24v (both sides ) after 2 seconds. It wasn't due to cold weather that it wouldn't start, I just seemed to lose any glow plug volts. I am pretty convinced the damage was done when I inadvertantly left the ignition on for several hours after searching all over for glow plug volts. Ignorance has won the day but I haven't given up (yet). I have removed all the dud glow plugs and the injectors and will attempt a magnetic solution although I think the glow tips are alloy. Vaccum cleaner? Nothing to lose. The last resort, of course, is to remove the head. Oh, I didn't drive the car when I managed to get it going.
 
What is the ignition light? The glow light?

If that went on but didn't turn off then that probably blew the plug itself immediately and then couldn't read any resistance. I would assume your glow system is fine, you just had some bad plugs.

Now to get the debris out of the cylinder. If you started it after, then you might be lucky and the crap was blown out with the exhaust.
 
Sorry! I called the sedimentor/alternator light my ignition light .( normally I'm a petrol head ). It now correctly goes out on START up since I had the alternator fixed. The glow plug light not coming on was the start of my disasterous fault finding exercise eventually leading to a broken glow plug. I believe the broken 12mm has gone no further than the top of the piston as initially inserting a new glow plug met an obstruction but slid in all the way after a little persuasion. I think a magnetic probe is not the answer as A. the probe is non magnetic and B. probing the injector hole for piston top meets the same level of resistance on all 4 pistons. I thought to try a vacuum cleaner but the obstruction puzzles me. I am trying to put off the evil day but think it means the head off. Any tips before I destroy any more of my cantancerous toy.
 
Back
Top Bottom