1997 Torque Steer and Vibration

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 16, 2012
Threads
5
Messages
16
Wondering if anyone could point me in the right direction.

My 97 has a very noticeable pull to the left only upon acceleration. It also has a vibration that you begin to feel in the mid 60 to 70 mph range.

I have had the front end aligned and it was in a shop with techs who were Toyota certified mechanics. They had it for a week trying to figure out why it behaves like this.

I am not able to work on my own rig, so I am at somebody's mercy for repairs. I don't mind paying someone, but I don't want to chase a bunch of wrong guesses while doing it. I have searched countless hours looking for answers.

Possible sources: birfs, u joint, tie rods, shocks, or other?

I would have thought it was obvious to a trained mechanic, but thus far it is a mystery. Also, I don't know if this matters, but when I turn the steering wheel to the left to full lock the front nose dips 1-2 inches. Turning it to the right doesn't equal the same result.

Any guidance would be appreciated.
 
What lift ? Alignment numbers ? Sounds like negative caster for steer , and tow out for pulling. track bar adjustment can do funky things with steer and pull too. Rear brake porportioning rod adjustment might be to tight and ddragging a bit if your , but that is u ssually more under deceleration. Does this happen when in low range when the transfercase is locked?
 
Are you sure that the right side has an axle shaft installed? Have you ever had the front axle apart and verified that all parts are there?
 
I would recommend posting your general location so that someone can point you in the direction of a cruiser mechanic who knows what they're doing. Keep in mind most mechanics at the dealer have probably never touched an 80 series.
 
It is stock as far as I know (no lift). I am in Springfield MO. I called one of the local guys on here and he recommended the shop to me as they had a couple of mechanics who were transplants from our local Toyota dealership.
 
It is stock as far as I know (no lift). I am in Springfield MO. I called one of the local guys on here and he recommended the shop to me as they had a couple of mechanics who were transplants from our local Toyota dealership.
Dealership techs are not necessarily your go to guys since the 80 is such an old model.
 
Dealership techs are not necessarily your go to guys since the 80 is such an old model.

Indeed. There are some embarrassing, even ponderous tales of dealer tech shenanigans here.

A _specific_ dealership can be great. Just being a toyota dealership doesn't guarantee that they will have any clue what they are doing.

Unfortunately, a lot of dealerships - not just toyota dealerships but dealerships in general - are hiring at lower and lower wages in the service bay, and it shows. Some managers are pretty sure that the service techs are just part changers and that if they do what the computer says everything will be fine. They're wrong.
 
A second shop spent another 2 days looking for cause of torque steer. "That's just the way it drives" I was told.

I started a separate thread for advice on local shops. There has to be reason, right?
 
Hate to resurrect this old thread, but still have the issue. Cruiser actually had radiator go bad so it didn’t go anywhere for a couple of years. Now it is back up and running with new shocks, tires, and other routine maintenance done. It still has vibration and pull to the left on acceleration though. Any help or suggestions are appreciated.
 
After searching through hundreds of posts, it seems maybe bad bushings could be the problem. Anyone have any thoughts?
Makes sense, sounds like there is something loose in the driveline and bushings are as good a place as any to start, also check rod ends and alignment again.....
 
Bushings you can check without taking it to the shop... to some extent. Park it with one tire up on the curb and crawl under and inspect the suspension bushings. If your truck is anything like mine, they will have visible cracks, and that's a good place to start (although probably an expensive job for labor--parts alone are $600 if you get all of them).

I don't know about the bushings causing such a specific pull, but I guess it's possible (if maybe the radius arm bushing connecting the right arm to the frame is shot, accelleration could cause the right side of the axle to move forward, mimicking the effect of steering left?) All of mine are shot and the truck drives sloppily, but doesn't favor one direction over another or any specific quirks other than driving like crap in general :o

Vibration between 60 and 70 sounds like a u-joint to me.
 
Thanks for the thoughts. I’m pretty sure the bushings have never been changed and it is very sloppy handling. I would hate to spend money on bushings if t didn’t fix the pull.
 
Back
Top Bottom