17" wheel questions?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 21, 2019
Threads
1
Messages
6
Location
New Mexico
First post for a newb to the forum. I am rebuilding my 76 FJ40 from the ground up. I would like to use a 17" wheel. I know the bolt pattern is a 6 x 5.5 and additionally the desired backspacing is 3.5". I did some searching on the forum but really could not come up with anything solid. Any additional advice on what to look for, where to shop at......ect? Thank you in advance
 
Last edited:
Seen folks mention Toyota's FJ Cruiser steelies work.

I've never searched iH8mud for 17" rim info, but you could. Here's one way—> Click advanced search, click "search threads" option, unselect search all forums, select search only 40 & 55 series forum. As far as search terms, I'd try [17"] [R17 wheel] [R17 rims] [17 wheels] [17 rims] ect.
 
Trust me I did an advanced search. Nothing really stuck other than getting the right back spacing which is 3.5". I just had also read something about making sure the rim clearing the hubs.

Thank you for the for the pictures and information. That sequoia rim really does looks good.
 
I've seen guys (here on Mud) run stock FJC/Tundra steel wheels, which are 17".

Your tire selection will be more limited with 17's though.
 
I've seen guys (here on Mud) run stock FJC/Tundra steel wheels, which are 17".

Your tire selection will be more limited with 17's though.

I think they run a spacer with them ... but... never had a set so do not know first hand ... only from reading

My reading and hearing has been hit and miss lately (according to wifey) :meh:
 
I don't have any hands on experience with the 17" wheel but I do have 16" Wheel Vintiques steel wheels on my 40. They are actually a 4" backspace and work fine. I had to make sure the clamp on the relay rod is turned out of the way and the tire will just barely touch at full left lock but no issues. Once you jump to a 16" and above wheel diameter, the tie rod issue goes away because it tucks inside the wheel. The center bore has to be above 106mm or 4.2 inches (most likely kinda sure on that one). So if you did go 3.5" backspace you have lots of room I believe

With 17" wheels you could do the standard 2.5" lift and get a 285/70-17 or a 255/80-17 to get a 33" tire but not too many brands on those sizes
 
I don't have any hands on experience with the 17" wheel but I do have 16" Wheel Vintiques steel wheels on my 40. They are actually a 4" backspace and work fine. I had to make sure the clamp on the relay rod is turned out of the way and the tire will just barely touch at full left lock but no issues. Once you jump to a 16" and above wheel diameter, the tie rod issue goes away because it tucks inside the wheel. The center bore has to be above 106mm or 4.2 inches (most likely kinda sure on that one). So if you did go 3.5" backspace you have lots of room I believe

With 17" wheels you could do the standard 2.5" lift and get a 285/70-17 or a 255/80-17 to get a 33" tire but not too many brands on those sizes
Any pictures of your 40 with the 16s? Thanks. Not to hijack the thread.
 
Any pictures of your 40 with the 16s? Thanks. Not to hijack the thread.
Here's one, plus one more
20181123_175658.webp

20190112_084738.webp
 
Last edited:
Those are ProComp Vapor 2. I've seen a ton of NOS for sale on craigslist and facebook. 4wheelparts replaced the vapor 2 with something else... I forget the name :doh:

*EDIT*
Here is one example that just popped up on me:


I found a lot of good looking beadlock rims I liked but didnt want the beadlock part. Still a very nice looking rim.
 
I appreciate the input and pictures. I went with these rims from Summit, Pro Comp Xtreme Rock Crawler Series 97 Steel Black Wheels 97-7983S3.5

View attachment 2151312
I too went to summit for 17" wheels. @dogfishlake is correct about the TRE and brake component clearance issue being minimized with the larger wheel. However tire rub on the tub and other items becomes a problem if you don't maintain the 3.5" BS on the wheel (also depends on tire selection). I'm very happy with the way mine turned out. I went 17x9 35x12.5 bfgs. I get a little tub rub under moderate flex.
fullsizeoutput_947.webp
 
I too went to summit for 17" wheels. @dogfishlake is correct about the TRE and brake component clearance issue being minimized with the larger wheel. However tire rub on the tub and other items becomes a problem if you don't maintain the 3.5" BS on the wheel (also depends on tire selection). I'm very happy with the way mine turned out. I went 17x9 35x12.5 bfgs. I get a little tub rub under moderate flex.
View attachment 2151500
That is the tire look I am going after. Looks good.
 
I liked these when they first came out on the 3rd gen 4Runner. Back then they were hard to find and expensive when you could. Have a one inch spacer on the front axle and spare on the back. They fit inside the fenders front and back. The clearance to tie rod ends is able the same as stock rims. Going with taller tires and keeping them tucked in as tight a you can you will hit the drag link sooner if your running the stock steering.

IMG_20190822_185941082.webp
IMG_20190822_190011688.webp
IMG_20190822_190232324.webp
IMG_20190822_190100793.webp
 
The 4" b.s. works with a 33" tire (10.5") wide. I wouldn't see it working with a 35"x12.5"
 
Back
Top Bottom