If you think you are good to get here and want an upper UCA in good condition (70K non offroading miles) I will bring one. We can install around the campfire.
100's In the Hills Yard sale
- Thread starter bluecruiser
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
If you think you are good to get here and want an upper UCA in good condition (70K non offroading miles) I will bring one. We can install around the campfire.
You too. I have both. I saw on the other thread you are getting it going.
I was, but a couple of members fell through on their commitments.
Let me know if anyone is interested in me bringing these.... otherwise I'm not killing my gas mileage even more for the 2200 mile trip 
- OME 865's (1 year old)
- Thule Load Bars for LC Factory Rack - Slightly used (hole in each for awning)
- LC Factory Rack with all hardware (Normal wear and tear/garage ceiling scuff marks - whoops!)
- LC Front Bug Guard - NIB
CruiserHead05 might take the springs if he quits being a turd and orders his diff drop.
- OME 865's (1 year old)
- Thule Load Bars for LC Factory Rack - Slightly used (hole in each for awning)
- LC Factory Rack with all hardware (Normal wear and tear/garage ceiling scuff marks - whoops!)
- LC Front Bug Guard - NIB
CruiserHead05 might take the springs if he quits being a turd and orders his diff drop.
PM sent
Anyone want a 40" Single Row CREE LED Lightbar. Unlike the cheap ebay ones, all the LEDs are 10W not 5. 260W Close to 22,000 Lumens combo beam 6000k White. I've used it on one trip. $375
Pics:
I'm also looking to pass my full LabRak set up on to another MUD member. (Awesome rack, but need the money for something else right now).
I have the following accessories for it:
5 3x1" Crossbars
6 Quick Release Tie down Rings
4-6 Screw on tie down rings
Hi-Lift Mount
Shovel Mount
Axe Mount
4 Yakima bar mounts
2 Awning mounts
2 Lightbar Mounts
PM me if interested.
Pics:
DROOLING over the whole setup!!! The last thing I need to "top off" my mall cruiser is a rack and a significant amount of light!...digging through the couch cushions now...
Sweet!
As for the boot kit, I was going to order last week for before the trip, however they are special order from Toyota and didn't want them to hold up everything else.
Just bring a grease gun with a needle and hit it every gas stop
[STRIKE]I just ordered one and[/STRIKE] there are aftermarket ones available. A new ball joint is almost the same price though.
Aftermarket: http://www.amazon.com/Febest-Toyota-Front-Upper-43324-69015/dp/B00C6MXSF4/?tag=ihco-20
Last edited:
Lower Ball Joint Boot Kit: http://www.amazon.com/4334569015-Lower-Joint-Toyota-Febest/dp/B00DMA976S/?tag=ihco-20
Bloomer - couldn't send pics via a PM, but I managed to snap some pics of the load bars. Again, I drilled for the awning mount I had, but otherwise are nearly new. Let me know if you'd like me to bring them along.
I have a factory Cat back exhaust that is in pretty good shape. Was cut off just in front of the resonator. $150.
Brand new never user transfer crossmember. $150
Brand new never user transfer crossmember. $150
Have a factory in-console 6-disc CD changer that i had forgotten about. Worked great when I pulled it. Cost: 1 beer.
Sent from my iPhone using IH8MUD, and hopefully approved by the NSA.
Sent from my iPhone using IH8MUD, and hopefully approved by the NSA.