clip

I'm in search of the specific name or part number for the small black clip located inside the steering wheel of my 80s Series Land Cruiser. Any assistance in locating this information would be greatly appreciated!

I am in the process of doing the rear disc conversion with the Monte Carlo Calipers. Do I need to use the clips that came with the pads for the outside brake pad? I have not seen anything about the clip in any of the write ups I have read, so I am guessing I do not use them, just want to make...

Hi all, nothing turned up in search so hoping someone can chime in for me. I'm missing the clip on my pull type glove box lid that actually holds the lid shut. Right now everytime I touch the loud pedal the glove box flies open and the passenger princess is starting to get rather annoyed by...

Need help from the collective brain here! Bear with me, as I don't know the actual part names, so I will do my best to describe! My LC seems to be missing a couple of the round plastic clips that holds the black plastic shroud thing that covers the headlight, radiator and where the hood latch...

Hi all, Attached is a STL file for the hood rod prop clip. I printed and tested the clip in various orientations. In terms of strength, I had the best luck printing in the two orientations shown below. Pictured below was printed at 100% infill and .3mm extrusion "draft" settings. I plan on...

One clip. 1 clip. Sólo uno. Seulement un. 唯一. 只有一個. Einziger. Ain’t but one. 60.00 plus shipping.

I have a bag of these from replacing mine a long time ago. They are not exact fit but work well enough. Give me an address and I'll send to you. And then pass the others forward. Or if multiple folks want I can send in envelopes. I think 6 left. -Corey

Beer emoji to who might know what this orange clip is called or the part number. I’m exhausted trying to find it. It’s on the drivers side near the fuel damper.

I use to make pictures of everything when taking all apart but here I missed one... It was stored in the back with the starter switch but I have no clue where it goes. Does anyone of you have an idea? BJ40 1977... Thanks!

There were several clips about LC assembling. This one in the nice quality

I just replaced the transfer case shift lever seat in my '93 4WD 4-Runner with the manual transmission. I'm having a lot of trouble holding down the metal cover against the force of the spring so I can install the retainer clip. Are there any tips and/or special tools that will make this easier?

Anyone ever had this issue? I rebuilt my knuckles, I've done it once before. But this time the drivers side axle won't pull out far enough to get the C clip on. With the spindled seated it won't move in or out at all like the normally do. The preload is right on and the axle is centered...

Despite trying many many times. With various jumpers of various metals. I can’t get it to work. Any ideas?

I am looking for a dash pad retainer clip. 55449-60010 my dash pad is ok but the metal strip that connects it to the dash is rusted to pieces. Thanks, Bob

I'm about to reinstall the cladding on my LX450 and am aware that there are two different types of clips that are used. Since nearly every clip broke during removal, I failed to notice which of the clips were the (impossible to remove) squarish 1-piece clips or the 2-piece (easier to remove)...

Looking for either version of the blue TEQ wrench clip. Willing to pay via PayPal, but let me know if you are looking for anything. Maybe we can make a trade. Thanks,

I've completed the tear down of my knuckles, received my new inner axle shafts, and I thought I was ready to rock this weekend to reassemble. Alas, I need new axle shaft C clips for the birf connection. Anyone got 2? I'd need them mailed priority to 08619 or 08501 and I'm fine with whatever...

I'm in search of the following for 5/1977 FJ40: 1 rear heater clip (see picture) Yellow jack handle Thanks Jeff