T case wont stop leaking!!!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 25, 2005
Threads
24
Messages
591
Location
Spring, Texas
well mine wont stop leaking, i have checked every nut, bolt and seal i could with taking it out. so i got the 500 watt work light and sat under the Cruiser just looking, well its got a nice CRACK thats about 4in long. does this happen alot? i think im going to get a just the case from the same year or get a ORION TRANSFER CASE . i like the ORION TRANSFER CASE because ill get lower gears and later down the line when i get a Toy box ill have super low gears! :flipoff2:

Grady
 
Grady - welcome.

You will probably keep those "super low gears :flipoff2: " turning a bit longer if you figure out why your case cracked...

The fine folks who read here could probably help you more if we knew more about your rig - year, model, engine, tranny, t-case, and mods. A description of where the crack is, or a picture is even better.

Good luck.
 
Let me guess, crack from the top cover down to the idler shaft?
 
PabloCruise said:
Grady - welcome.

You will probably keep those "super low gears :flipoff2: " turning a bit longer if you figure out why your case cracked...

The fine folks who read here could probably help you more if we knew more about your rig - year, model, engine, tranny, t-case, and mods. A description of where the crack is, or a picture is even better.

Good luck.


yep right on! its a 1980 FJ40 Stock 2f.
 
I had a similar problem. The PO had welded it and used Pink permetex. Still leaked a little. Ended up replacing it.
 
teapot said:
solution 1. weld the crack if you can
2. get a used housing and replace
3. buy the orion for lower gearing $$$$
4. wait for the orion hd $$$$


i know the orion t case is like 1500 to 2000, but how much would the orion HD run me? any one got or know some one with a 7/87 to 7/80 t case? i might even try to find a whole tanny and t case and rebuilt the tranny and sell it, make some money back.
 
Wish I had 2K to throw around.

A Saw a commercial on a product called alumiloy (SP) Looked easy to use. for aluminum. and all you need is a propane torch. Canoes and Transfer cases are two different things, but it might save you some dough. Then get a t case saver.

I would at least try it. and spend the rest of the money on beer and 8tracks.
 
Don't toss the 4 speed case. There are some parts on it that I would like to get my hands on as I'm going to be using a 3 speed case with a 4 speed tranny. PM me and we can talk.
 
im just going to pull it and see whats up ill keep you guys updated.
 
FJ40onNOS said:
i know the orion t case is like 1500 to 2000, but how much would the orion HD run me? any one got or know some one with a 7/87 to 7/80 t case? i might even try to find a whole tanny and t case and rebuilt the tranny and sell it, make some money back.


Orion HD WILL NOT have provisions on the rear of the transfer case for a speedometer drive, nor will it have the rear housing that mounts the parking brake assembly....just FYI....



I have a complete trans and tcase removed from a 1978-40 series that was gone through a couple years ago....it was taken out for a non-USA four speed and an Orion...



Good luck!



-Steve
 
by Orion, you mean the t case i was taking about right?
 
Yes.


The standard Orion cast iron transfer case was designed to be a replacement alternative/low gearing option for Land Cruiser owners that have a one-piece transfer case that did not want to build a new rear axle in order to run a different transfer case.

The idea, according to AA with the Orion HD is to offer a 4:1 and 3:1 gearing option to people that are using the Dana 18 transfer case in earlier CJ's, and a stronger alternative to those running a Land Cruiser, but who are not concerned about having the parking brake on the transfer case, or having a mechanically driven speedometer.


Klear as mudd? ;)


Good luck!


-Steve
 
im going to try some JB weld just so it will hold some oil when i drive, until i can get it replaced
 
FJ40onNOS said:
im going to try some JB weld just so it will hold some oil when i drive, until i can get it replaced

Don't wait too long. There have been posts on here where the transfer case guts fell out on the trail! When that happens you're DOA.
If you get a standard transfer case get the case saver as well to lessen the chances of a similar problem in the future.
 
ya a t case saver is something i am going to install, who makes the best!
 
Back
Top Bottom