couple questions on using 60 axles

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 1, 2005
Threads
87
Messages
2,331
Location
USA
first of all, is there any difference in width between 40 and 60 axles? i tried the old search method, but nothing really turned up. from what i have read, it sounds like they're an almost direct bolt in. also, am i correct in saying that a fj-40 fine spline 9" 3rd will fit the 60 housing without any problems? this would be to get a 4.11 gear ratio as opposed to 3.73.
 
JJS said:
first of all, is there any difference in width between 40 and 60 axles? i tried the old search method, but nothing really turned up. from what i have read, it sounds like they're an almost direct bolt in. also, am i correct in saying that a fj-40 fine spline 9" 3rd will fit the 60 housing without any problems? this would be to get a 4.11 gear ratio as opposed to 3.73.

the only things i can think of are the Spring Perch, have a different size hole in the middle where the center pin goes in, and tabs for the parking brake stuff. thats all i got :D
 
thanks. do they have any more caster than 40 axles, or are they about 1* too? i'm guessing it's the same since no front axles that came from the factory spring under had any caster.
 
Pumpkins are interchangable, but like Bruce says the perches are spaced wider apart. You have to "outboard" the spring hangers. Do a search on outboarding and you will find some stuff. There are some differences in the axle lengths and birfs too. Look in the tech trivia section and it will list all that stuff.
 
I'm setting up a 60 rear in my now. You have to relocate the spring perches and since I'm lifted I went ahead turned the pinion up a couple of degrees. The short side axles are the same but the long sides are different.

I'll be running 60 axles front on rear on my daily driver project and it looks like outboarding the springs 1/2 to 3/4 inch will get it. There is thread with pics of the outboarded spring hangers somewhere on here that I can't find right now.
 
JJS said:
first of all, is there any difference in width between 40 and 60 axles? i tried the old search method, but nothing really turned up. from what i have read, it sounds like they're an almost direct bolt in. also, am i correct in saying that a fj-40 fine spline 9" 3rd will fit the 60 housing without any problems? this would be to get a 4.11 gear ratio as opposed to 3.73.

Are you looking for a wider width axle housing and different diff ratio? Or do you want just the different gearing? If it's only gearing then you could swap the inards of the 60 into the 40 housing minus the long axle which you will have to use out of the 40. This gives you disk brakes, better birfs without the spring issue and keeping it stock looking.
 
I'm very pleased with having fj60 housings under my cruiser. The width is perfect, and you dont' have to use spacers. It isnt' much work to outboard the springs, and I feel that my suspention is very balanced front a rear with the outboarded front. Of coarse i'm running xj springs in the back too though.
 
i read thru your swap thread, and it all looks pretty straight forward. only thing i'm wondering is did you make the shackle hangers or are they fronts welded in the back?
 
yeah the shackle mounts are the OG ones chopped up a bit to make them as low as possible, and of coarse outboarded and triangluated. I think I outboarded 1.25" on either side if I remeber correctly. I wanted to go thru the frame for the shackle mounts but my header was in the way. I would recomend buying the fixed mounts from proffits, they are very nice and beef aswell as cheep.
 
width as well as having the best toyota parts: large steering knuckle bolt pattern, vented rotors with 4 piston calipers, mini truck style birfs and hubs. fj62 axle would be ideal, with its housing gusset, and fine spline 4.11s
 
Back
Top Bottom