yeah I checked belmetric but I was not excited about how many threads there were on the bolt.
I know thats sounds dumb but it seems the stock bolt does not have threads on most of the bolt where it goes through the bushing.
I guess all of that...
Well I'm a moron and decided that I was never gonna use whatever size bolts are used in the front suspension arms so apparenly I tossed'em or something because I can't find them.
The bolts for the arms are not really the problem since I bought...
Yeah I emailed Zuk yesterday right after I posted my message above.
He noted that some people have removed that retainer but maybe that isn't the best Idea.
He stated that he has flared the retainer up some as well as clearanced the spacer some...
Ugh I am never going to get this thing together
So I finally got my solid pinion spacer and slide it over the pinion and go to slip it in the diff housing and the spacer hits the oil retainer ring before it even gets close to seating against the...
Yeah I got the flange at the same time.
If I recall I started trying to get the Revolution gears from Poly Performance.
After I did not receive my gears like 2 weeks later, I then sent a message to see what was up.
They told me it would be about...
Hmm that's a good idea. I will see what the rear on mine looks like before I tear it apart.
I also wonder if the natural wear on the gears over that kind of mileage is responsible for the poor mesh pattern?
My rig has 280k miles on it so I'm...
I am doing a 4.88 gear swap.
I went through a whole debacle trying to get my hands on a set of Revolution gears but after more than two months of being told they are about a month out and still getting nothing I was eventually offered a set of...
That's kind of all I was looking for, someone that has maybe done a couple and what they have seen.
Naturally I decided that I was indeed going to run it that way.
Hence attempting to run the crush sleeve and installing the pinion seal.
But...
I think I am done ordering things from Poly Performance.
Placed an order for a solid pinion spacer on OCT 11 and they charged me $19 shipping for a $35 part that is like 2.5 inches by 2 inches and the damn thing is not going to be here until the...
Well I managed to move mine up quite a bit just being really careful bending the tubes.
However, as you can see it now occupies the space where the marker light is supposed to go.
I did come up with a "fix" but it was pretty invasive.
I hacked a...
Well, as a note to anyone attempting to take on a gear swap for the first time on their own, I should point out that the instructions for final pinion assemlby is not for a crush sleeve installation.
It is the install process for a solid spacer...
well decided to tackle this air locker and gear install myself because it just seemed like a thing I should know how to do at this point.
Following the manual they have you pretty much do the entire set up to get the pinion depth set then you...
I'm part of the pressure washer crowd
I use Purple Power degreaser in one of those garden sprayers with the pump so you can pressureize it.
Liberally hose everything down in the engine bay with the degreaser and let it sit for a minute.
I...
I literally just went through nearly the exact same issues when digging into my front axle.
I could type it all up here but it might be easier to just link my thread so you can see what I did for everything.
Hammers 80 series refurb
After looking at a lot of other bushings I have come to the conclusion that 26mm is definitely not correct for a 29mm bar ( I mean obviously)
Just going to give the plain ol' greasable energy suspension bushings from rock auto a try since I am...
Was starting to put my front suspension back together and wanted to clean up/freshen up some things.
One of those things is the Anti-roll bar bushings.
My first thougth was to just run some rubber OEM stuff but I starting thinking about the...
Sorry about that I had to relearn how to put pics in a thread from a hosting site.
Anyway as you might have gathered I did the necessary clearancing to fit the 4runner brakes
Just a little work with the die grinder and the caliper ears clear...
Well I couldn't help myself.
I ordered up an iBooster and harness from ebay and picked up one of Torfabs iBooster adapter kits.
That should just about cover all my brake upgrade.
Now I need to take a look at some electric power steering.
Not that it really matters for me since I have a couple options for alternator upgrades but has anyone had any issues with the power this thing could potentially use vs the Stock LC's lame 80 amp alternator.
Assuming since it uses a 40amp fuse...