Recent content by tolvota

  1. tolvota

    Dobinson 2.5" lift

    Offroad is mostly National forest camping in Florida and Georgia. Sand, mud and uneven terrain. Very little, if any, rock crawling. I'll dial in the T-bars and drive for a while. Thanks for the insight!
  2. tolvota

    Dobinson 2.5" lift

    Is the Dobinson lift kit the gold standard for the 100 series? They are definitely the most expensive. Is it worth the extra money? My application is 80% highway and 20% offroad. My daily driver. Mainly want a more level stance without compromising my CV axles. Seems like the Dobinson kit checks...
  3. tolvota

    Brake Booster Oil Pressure Connector?

    Hey Everyone... I received this remanufactured booster this afternoon. I bought it from an ebay supplier. I sent them pics of my old one and my VIN so that I would get the correct booster, Here's the issue: Note the different connector from the new booster to the old one. Am I supposed to splice...
  4. tolvota

    Overheating after Timing Belt Replacement

    Update - Retraced my steps back to removing the fan, drive belt and Cam covers. Hand rotated the motor through multiple cycles to verify timing marks are aligned properly. Removed the Cam position sensor and saw this. I did not remove it the first time and I nicked the wires when I installed the...
  5. tolvota

    Cam Position Sensor Replacement

    I removed the plate and installed the sensor and everything works as it should. Thanks
  6. tolvota

    Cam Position Sensor Replacement

    This is my old and new Cam sensor. My question is, does the metal plate need to be removed for installation? Thanks,
  7. tolvota

    Overheating after Timing Belt Replacement

    Just squeezing the upper and lower hoses.
  8. tolvota

    Overheating after Timing Belt Replacement

    I did my timing belt/water pump replacement this weekend. I'm at 221K miles. The original one was done at 129K. The old belt looked fine when removed. Also replaced the fan pulley. Everything went according to plan. Started right up once I remembered to put the MAF sensor back in place. Runs...
  9. tolvota

    Torsion Bar Adjustments

    Finally got my bars to adjust. Put it up on a friend's lift. After a lot of wire brushing to remove the undercoating on the threads, multiple soakings with PB blaster, a 3/4 breaker bar and a 3 foot pipe, they finally broke. Was then able to use a 3/4 inch impact. Did 4 rotations and my front...
  10. tolvota

    True Drive Front Axle Kit

    Anyone familiar with this?
  11. tolvota

    Torsion Bar Adjustments

    lol... thanks. That's actually very encouraging. Pretty sure mine have never been adjusted and with the undercoating it's that much harder.
  12. tolvota

    Torsion Bar Adjustments

    There's plenty of room to adjust, maybe 1/3 of the bolt. I didn't try to adjust while in High. Will give that a try along with my breaker bar and a pipe if necessary.
  13. tolvota

    Torsion Bar Adjustments

    Hey Everyone... Wondering what I'm doing wrong on adjusting the torsion bars on my 06 LX. I have an OBD scanner that can read the AHC pressures. Following the great video from YotaMD . My pressures are high in the front so I am trying to turn the adjuster bolt on the torsion bars... it won't...
  14. tolvota

    2006 Lexus LX470 VGRS issues

    Well... Made some progress today. Had both VCS lights on and the VGRS light on. Bought a DLC extender cable and performed step 8 from the VGRS system calibration procedure posted in this thread somewhere. No change and I felt kinda silly doing sub steps 1-6 15 times. After driving it again and...
Back
Top Bottom