Recent content by Swede4477

  1. S

    Need new hose for clutch slave cylinder

    Thank you very much! That's exaclty what I was looking for!
  2. S

    Need new hose for clutch slave cylinder

    Do you know if 3/16” hard line will work with the 10mm fittings needed for each end?
  3. S

    Need new hose for clutch slave cylinder

    Thank you for the info.
  4. S

    Need new hose for clutch slave cylinder

    Thank you for the info. Is your slave on the same side as the master? Mine is on the opposite side, which is why length is a concern.
  5. S

    Need new hose for clutch slave cylinder

    The hard line is about 60", though I haven't removed it yet. Adding another 17.5" (length of the soft line to the slave) would mean I'd need about 80 inches. If I try the soft line, I'll have to route it differently to make up for some length. I tried flaring one end of the existing hard line...
  6. S

    Need new hose for clutch slave cylinder

    Very cool pic. I've always been a fan of Billy the Kid. Thanks for the info. I definitely wouldn't replace a hard line with steel for brake lines, but where this is for the clutch I may try it. Agreed on the quality of eBay parts at times. I willl be sure to verify with the seller that the hose...
  7. S

    Need new hose for clutch slave cylinder

    Also, this is the hose I found on eBay:
  8. S

    Need new hose for clutch slave cylinder

    Hello. I have a 9/'74 FJ40 and am rebuilding the clutch master cylinder and replacing the slave. I also purchased the soft line that connects the slave to the hard line from the master. I also need to replace the hard line and in searching online I have found that there is a 65" stainless steel...
  9. S

    Misc Torque Specs - Use at your own risk! (FAQ)

    Thank you very much. I figured they wouldn't need much. I intend to make my own gasket using Fel-pro Rubber-Fiber gasket material and was thinking of adding a thin coat of Permatex High Tack sealant to each side.
  10. S

    Misc Torque Specs - Use at your own risk! (FAQ)

    Wondering if anybody knows what the proper torque is for the transmission side cover bolts for a '74 FJ40? The cover is leaking on mine and I am changing the gasket. I can't seem to find it in the Haynes manual and I've tried searching on here but haven't found anything. Thank you.
  11. S

    '74 FJ40 - Sudden idle issue

    Howdy. My ’74 FJ40 developed an idle issue this afternoon and I’m looking for some guidance on where to start. I recently rebuilt the Aisan carb and had a ported vacuum port installed in the throttle body (thank you FJ40Jim). I also installed a new HEI/DUI distributor along with plugs, wires, a...
  12. S

    Rertrofit 1978 2F with 1992 3VZE Evap System

    I do have the check valve by the fuel tank. I took it off and put air to it and it seems to work as it should. Thanks for the input.
  13. S

    Rertrofit 1978 2F with 1992 3VZE Evap System

    Thanks for the input. After further searching on the forum, I found out that all '69 to '74 Fed-spec carbs have no ported vac fitting, so the port at the base of my factory Aisan carb is for manifold vacuum. To be sure, I took it off and saw that the port is below the butterfly. I had installed...
  14. S

    1974 vacuum line diagram

    Good to know. Seems like it must've been manufactured that way for some reason. Thanks for getting back to me.
  15. S

    1974 vacuum line diagram

    Howdy. I realize this post is 10 years old, but I’m looking to replace the pcv hose on my ‘74 FJ40 and I too have a different diameter on the port on the base plate of the carb than on the pcv valve. The diameter on the valve is 10mm while the diameter on the port on the carb plate is 13mm. I...
Back
Top Bottom