Recent content by relaxing

  1. relaxing

    2008-2018 Radiator Failure and Public Service Announcement

    Thanks It's too damn cold out in the NE right now and I don't have a garage to work in. Anyway I got my fill of wrenching doing the AHC over the summer to last me a while lol.
  2. relaxing

    2008-2018 Radiator Failure and Public Service Announcement

    So what’s a dealer radiator replacement running these days? Asking on behalf of the pink spray in my engine bay…
  3. relaxing

    LX570 AHC “Basics” - Added as sticky thread for AHC Issues

    Other notes from completing the fix: - Pulling the exhaust and the spare helps massively with getting into things. Even still, the underside is deceptively tight to work in. There's always a bracket or a frame member right where your wrench needs to be. The AHC lines were clearly designed to be...
  4. relaxing

    LX570 AHC “Basics” - Added as sticky thread for AHC Issues

    Well I did it. It took the job from nearly impossible to downright manageable. If that 1" gap is what eventually takes down my LX... tell Akio Toyoda she died historic on the fury road.
  5. relaxing

    LX570 AHC “Basics” - Added as sticky thread for AHC Issues

    Was debating this - on one hand it’s an obvious failure point. On the other hand Toyota was concerned about the hydraulic fluid heating up. And the line lasted 15 years - in the rust belt - and if it goes another 15 years the entire system will be due for an overhaul anyway.
  6. relaxing

    LX570 AHC “Basics” - Added as sticky thread for AHC Issues

    Got a buddy to help wrench it out the hard way, 1/8 of a turn at a time. Failure analysis: pinhole leak at the heat shielding wrap. Kind of amazing it was able to empty 2 liters through that tiny hole in such a short period of time.
  7. relaxing

    LX570 AHC “Basics” - Added as sticky thread for AHC Issues

    Or to really get desperate, would anyone recommend for/against cutting into the wheel well here? (right below that circle)
  8. relaxing

    LX570 AHC “Basics” - Added as sticky thread for AHC Issues

    Trying to get to that impossible rear no. 5 height tube union on the pump side... Of course mine is seized and finessing it with a crowfoot wrench isn't working. Has anyone removed this bump stop? Apparently what Toyota calls 52216-60050 Stopper, Cab Mounting Cushion Getting it out would gain...
  9. relaxing

    SQOD Squad - Stupid Question Of the Day

    The trick was to get the rear end up another foot with a big jack. My 8” ramps + ahc slammed in low = not enough ground clearance to swing the tailpipe over the axle.
  10. relaxing

    SQOD Squad - Stupid Question Of the Day

    next dumb question, is there a trick to snaking the exhaust around and off the rear axle and frame crossmembers?
  11. relaxing

    SQOD Squad - Stupid Question Of the Day

    thanks for that. the dealer site i was on just wasn’t giving it to me. partsouq had the diagram right away.
  12. relaxing

    SQOD Squad - Stupid Question Of the Day

    Thanks! So looking at an online parts catalog, the diagrams for the various systems don’t list the fasteners needed? Where do people get diagrams like this? Or to get to the point, what bolts are needed for the exhaust system? I’m going to drop the exhaust and I’m expecting it all to be badly...
  13. relaxing

    SQOD Squad - Stupid Question Of the Day

    The Service Manuals don't list part numbers for anything. Where does one find the part numbers?
  14. relaxing

    My AHC failed

    Starting to assemble the parts and tools for the job… Figure I’ll replace the globes while the system is empty as well. I’m assuming it’s going to be the 48998 line but I’m wondering if there’s any troubleshooting to do to make sure that’s the leak and not anywhere else. Short of filling it and...
  15. relaxing

    My AHC failed

    The side above is pretty dry. Here’s the wet side (towards the wheel.) The union nut (?) The entire frame is soaked up to the Center Unit. Opinions welcome.
Back
Top Bottom