Recent content by PNWLX

  1. PNWLX

    FN Wheels : 100-Series Specific Wheels

    @Irishpilot , I had the same trouble with 'bonus material' on my hubs. Just like you, a Dremel made quick work of it and then they fit great. For what it's worth, they look good dirty too :-)
  2. PNWLX

    3rd cylinder miss with eaten injector harness

    Yea. There were eBay ECU repair options too, but the UPFix site had a more professional vibe for whatever reason. I don't know anyone that's used them before. Super glad it all worked out. You are right about Mud being the exception, for the most part, for people posting the final episode of a...
  3. PNWLX

    3rd cylinder miss with eaten injector harness

    UPDATE (mostly because it's good news, but also hate finding forum posts from years past where we never see if the thing got fixed or not...) Can't believe it's been exactly a month since this first came up! I reached out to UpFix with what troubleshooting had been done so far and they were...
  4. PNWLX

    3rd cylinder miss with eaten injector harness

    I had that realization last night that I neglected to test the injector 3 wire with it disconnected at both ends. Did that this morning and re-confirmed the wiring is good. Showed 000.2 Ohms of resistance, which was the same as the neighboring injector (also disconnected from the ECM and the...
  5. PNWLX

    3rd cylinder miss with eaten injector harness

    Just did this, and finding the same at the ECM. Checked continuity between the wire coming out of the harness and the one at the injector plug first. I'd note that the problem injector plug (3) shows constant 12v when the ignition is on, where the others don't - as they are awaiting the ground...
  6. PNWLX

    3rd cylinder miss with eaten injector harness

    It does seem risky that a shorted injector wire could cook the ECU... the repair is solid at that obvious point of failure, and I couldn't find any other suspect rodent attacks nearby, but I'll trace it back further tomorrow. I'll also see how it compares with the outputs on the ECU itself...
  7. PNWLX

    3rd cylinder miss with eaten injector harness

    Finally got a proper plug with new leads to test with today, just in case my re-pinning of the old one was making for a bad connection. No luck. Resistance was about 11.3 Ohms, which seemed about the same as the neighboring injector (it's 40F outside). I also applied 12v directly to the...
  8. PNWLX

    3rd cylinder miss with eaten injector harness

    06 LX470 Yesterday we noticed she was running a bit rough right as we left the house for the day. Within the block it threw a code so we parked it. Scan gauge said it was a 3rd cylinder miss. I immediately assumed coil pack, so I swapped it with cylinder 1 to see if the issue followed the coil...
  9. PNWLX

    CarPlay and Android Auto installation into Toyota Land Cruiser 2004-2007 GROM VLine

    Is there a world where one could replace the factory screen itself (06 LX470 w/nav) with something more modern and higher resolution, while still retaining communication with HVAC and the VLine? We love the VLIne, and only recently have used it beyond it's Android Auto capabilities. The OEM...
  10. PNWLX

    Ben3D fogs on the LX (turn signal relocation)

    The factory wiring reached up to the corner lights, as long as you cut a couple of the zip ties along the way. I should add that it's possible that you could just re-wire the factory corner lights to be turn signals, mine have been burnt out for years, so I didn't have a bulb to test that...
  11. PNWLX

    Ben3D fogs on the LX (turn signal relocation)

    Here's the section I intended to cut out of the rear of the corner light housing. I filled the cavity of the housing with a shop towel, to help keep debris down. A cutting wheel on the Dremel knocked off the old boss for the old bulb, then a step bit opened it up enough to fit the turn signal...
  12. PNWLX

    Ben3D fogs on the LX (turn signal relocation)

    Finally snagged a set of @BenCC fog lights for our 06 LX. Quality is top notch, which isn't a surprise since we already rock a Scangauge mount from Ben. The included wiring harness is a really nice touch. One thing us LX folks have to deal with when replacing the OEM fogs, or bumper, is what...
  13. PNWLX

    Media The MUD 100 series Photos thread

    Working our way home from an amazing trip up to northern British Columbia.
  14. PNWLX

    LX470 third brake light

    If you don't have luck finding a used one, I bit the bullet and got a new one off ebay from the UAE. Here's the seller I ordered through a couple of years ago. It was definitely OEM and hasn't leaked. https://www.ebay.com/itm/255752502091
  15. PNWLX

    FN Wheels : 100-Series Specific Wheels

    This was just a night at Cape Disappointment here in Washington. It's a great state park for the trips we'd prefer to have a reservation and is close to home. In this case we had friends already going so we just took over their parking spot at their site. Perks of the rooftop tent. They...
Back
Top Bottom