Recent content by mircea163

  1. mircea163

    3B/13B-T Fan Clutch and Fan Upgrade

    My '87 Spanish model BJ73 does have the lip. I already have the HDJ fan, shroud, and radiator. I will post how it goes, but it will be while.
  2. mircea163

    3B vs 3BII

    Can i use a 3BII crakshaft on a 3B engine ? The parts seem to have different numbers, 13401-58020 for the 3B and 13401-56040 for the 3BII, but i thought i would ask, anyway, i'm really grasping at straws.
  3. mircea163

    3B/13B-T Fan Clutch and Fan Upgrade

    Very interesting mod, i may attempt it myself one day, thank you for sharing. Any updates, is everything working as it should ?
  4. mircea163

    BJ73 cranks, starts, dies

    I did anneal them, forgot to say, but i also sanded them beforehand, i didn't think about contamination. I have ordered spares, but i got impatient waiting. Anyway, they seam to be sealing fine, maybe i just got lucky.
  5. mircea163

    BJ73 cranks, starts, dies

    Well, it turned out to be a bad gasket somewhere, probably the ones connecting the feed pump to the pipes, a little bit of air was getting in. I sanded and straightened the gaskets i didn't have spares for, and voilla, the car now starts. Now on to the knocking sound, there's always something.
  6. mircea163

    Is this the sound of a rod knocking 3b bj60?

    I know it's an old topic, but i am having a very similar noise on my 3b, did you find out what it was ?
  7. mircea163

    BJ73 cranks, starts, dies

    Thank you for doing the leg work. I do have a oil pressure and water temperature Redarc gauge awaiting to be put in, so i may just discard the other sensor altogether, once i fix the issue.
  8. mircea163

    BJ73 cranks, starts, dies

    1987 3b, inline pump.
  9. mircea163

    BJ73 cranks, starts, dies

    I thought the EDIC was doing that. My EDIC is out, but the sensor is still in, is there something else controling this ? The oil level is fine, so maybe a faulty sensor ? I will order a new sensor, anyway.
  10. mircea163

    BJ73 cranks, starts, dies

    Any advice would be appreciated, i am running out of ideas. The engine fired immediately every time, car ran fine, but one day, after some 5 km, it started to loose rpm, even while i was giving it gas, and died. I restarted it, started fine, but immediately began to loose power, died again, and...
  11. mircea163

    1987 2h- rebuilt my injectors, truck lost power and won't start

    I cleaned everything, replaced the nozzles and pressure set the injectors at 1750-1760 psi. I used shims for the old mercedes engines, they were a perfect fit. No leaking so far, but the car is not yet drive-able, that will be the real test.
  12. mircea163

    1987 2h- rebuilt my injectors, truck lost power and won't start

    Thank you, i won't use it again, then. The only parts i am truly concerned about are the mating surfaces, i have new nozzle assemblies. I've ordered an injector cleaner, but parts do take some time to get here. I will let you guys know how it goes, once i have everything back together.
  13. mircea163

    1987 2h- rebuilt my injectors, truck lost power and won't start

    Thanks, i will look into it. I used a brass brush to clean them, i'm still not happy with the result, though. Edit I also used a lot of Wurth brake cleaner.
  14. mircea163

    1987 2h- rebuilt my injectors, truck lost power and won't start

    Is this excessive crud buildup on the nozzles and inside the nozzle holder ?
  15. mircea163

    1987 2h- rebuilt my injectors, truck lost power and won't start

    I believe that is exactly the one i have, from mercedessource. I haven't used / tested it yet. Thank you :)
Back
Top Bottom