Recent content by JohnPro992

  1. JohnPro992

    Toyota B Main Bearing Torque Specs

    wow thank you so much, any wonder I screwed up my bolts, I just bought some bolts from an old B block in a wreckers. These have 19mm heads so I'm guessing its the 16mm. I dont know how the manual expected these to handle 145ft lbs. From experience 100ft lbs is plenty so I'll use that figure...
  2. JohnPro992

    Toyota B Main Bearing Torque Specs

    Hi guys, I need help. My manual says 145ft lbs. I am trying to achieve it but in the process stretched 4 bolts. Why does it seem so tight? I am using a 50-220 Torque wrench. I have reused these same bolts twice as this is the second overhaul. Are my specs right or are the bolts too old? I...
  3. JohnPro992

    Connecting Rod bearings 1.25mm B engine

    Machine shop can make bearings, don't know why they didn't suggest this in the first place. Thanks anyway guys.
  4. JohnPro992

    Connecting Rod bearings 1.25mm B engine

    Guys, I have a problem. I spun a conrod bearing because I ran out of oil pressure. I was going up a hill and it stalled, when I started it I didn't realize it had 0 oil pressure. I don't have the EDIC. Anyway the machine shop says I need 1.25 oversized bearings to get the crank back to normal...
  5. JohnPro992

    no oil pressure after rebuild - B engine

    Thanks, I will get a thermostat... When I start it up cold the pressure is at 20Psi... After the temperature reaches about 50-60 since no thermostat the pressure drops to about 10. After driving around for a while the pressure is about 5psi idling. I think I have cheap crap oil that is...
  6. JohnPro992

    no oil pressure after rebuild - B engine

    Guys thanks for the input, I put all your ideas together and now it works great. I kept the gasket on it and the clearances using a feeler gauge are all within spec according to the manual. I can turn it freely with my hand and there is a clearance from the gear to the cover but the pressure...
  7. JohnPro992

    no oil pressure after rebuild - B engine

    Thanks Gerg, I can see how difficult the priming is, I thought I could just pour oil down the check valve hole with the check valve removed. @Dan yea no gasket was mentioned in the manual, but it did have a gasket when I opened it, if I dont put any gasket is it normal for the cover to push...
  8. JohnPro992

    12V Lights Wire in Series - Why Don't They Work

    That's very interesting, I do get your point, so basically 2 pieces of 12volt bulbs running in series requires a 24volt source? And 3 pcs of 12volt bulbs in series requires 36volt source? And so on? If so amazing.. Just learned something new. Could I run any most 12 volt devices in series or...
  9. JohnPro992

    Amplifier 12v or 24v?

    good thread, will revive, i also have this issue and all stepdowns are 30 amps max, I figured 12V x 30amps = 360watts total Per step down. Is this correct? I ignore all the marketing BS and like to stick to the actual consumption or rating. :-)
  10. JohnPro992

    12V Lights Wire in Series - Why Don't They Work

    What's the benefit of running in series? If 1 blows they all go and all need to be checked, why not do what was mentioned in post 2? Just curious..
  11. JohnPro992

    Will an engine rubuild kit make the engine as new again?

    agree with Jan, the kit alone is not enough, it will cost a lot or a bit more to have that ALL new engine. Crankshaft can be machined and bearings oversized. I also noticed replacement pistons dont last as long as original. My replacement pistons from thailand or taiwan no longer has the oil...
  12. JohnPro992

    no oil pressure after rebuild - B engine

    :-( sad face... After rebuilding my motor, I started it up and ran it for 1 minute and the oil pressure didn't rise. It was 0 both on electronic and manual gauges installed on my rig. I have it all apart again. To inspect bearings and pistons incase I had it running too long. All seems okay...
  13. JohnPro992

    which way do the rear springs go?

    Thanks man! I assumed the same, the "mil wrap" are the 2 wrapped top springs around the spring eyes right? That should be on the fixed point. The side with the mil wrap is the shorter side on my springs. I am not sure of the brand, they might be original replacement for the FJ45.
  14. JohnPro992

    which way do the rear springs go?

    A bit of an emergency post. Im at a shop right now and noticed the longer side of the spring is facing the front of the car. Its an FJ45 chassis... Shouldn't it be the short side towards front of car? Im refering to rear leaf suspension. The short side to the fixed mount and longer side to the...
  15. JohnPro992

    What is wrong with this GLOW PLUG diagram?

    thanks @RufusTheDufus ! Yep that will be my solution for now :-D a fixed timer setup. :cookie:
Back
Top Bottom