Amplifier 12v or 24v?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

fireball

SILVER Star
Joined
Jul 17, 2013
Threads
65
Messages
3,378
Location
southern VT
I have tried to search but keep coming up with arguments on how to keep my 12V stereo from loosing memory!

I'd like to put a 4 channel amp into my BJ74 which has a 24V system to run a decent set of 5.25" components and a single 10" sub. The biggest step down convertor seems to be this one from Pyle, a 720W peak, 360W continuous that can only run 30 amps. Most decent 4 channel amps seem to need more juice than that.

What are you all doing for music in your 24v trucks? Listening to the sweet sound of the diesel? A quick search for 24v amps lead me to this as the cheapest option, which is far from cheap! $430 JL Audio 24v marine amp

Any great ideas out there? Thanks!
 
Once you have the 24V to 12V converter you also have 12V for your memory available except when you turn off the converter of course.
Search for a converter that has a special 12V memory line even when the converter is "off". In other words: it has a back up battery for this purpose.

Or be creative and use a 12V battery for the memory back up.
12V battery.webp


Rudi
 
Last edited:
I considered a second alt to a third battery to run a 12 volt system, but I think it's more trouble than it's worth.

I think there are other higher amp converters out there, but I'm not sure what kind of tax on the system they will cause.

Ground Zero also makes some 24 volt amps. I am considering this route, but I wonder how long my alt will last running 2 24 volts amps??:meh:
 
Rudi, that is not my question. That question has been covered many times before :)

I am asking if people have been able to find affordable 24v amplifiers, or if they are using 12V amps powered from a step down convertor. The biggest readily available relatively common converter seems to be the Pyle units that are 720W max, 360W continuous, with a 30amp rating. I'm wondering how big/powerful an amp that converter could really run.
 
There are options out there, they are just a bit hard to find.

You can do it very easy and buy one of Pyle trucker series amplifiers.
PLTA180 and PLTA580. Not to expensive, if expensive at all. Well suited for 24v applications.

I have the biggest, PLTA580 and it is huge. You will struggle to find a good location for it.
file.php

file.php
file.php

That is a standard 20 liter plastic jerry can.

The smaller (shorter) and cheaper PLTA180 are more than enough for most.

There is a more efficient, but harder solution to this problem as well.
My intended use for the Pyle amplifier are to run my two subwoofers. For my components I am building a class T (D) amplifier that runs on a Texas Instrument TAS5630 chip. This amplifier will give you 2x300w in 4ohm with a bit of distortion when given 50v supply voltage.
They are cheap to buy pre assembled on a tiny PCB, only thing needed are a potmeter to set input signal strength and you are good to go and it is so tiny that you can hide it anywhere under the dash, seat or console.
About 60$ a piece.
572969681_825.jpg


They run on anything from 20v to 50v so it will run straight from the battery voltage, but at a lower max amplification.
At 28v it will run a pair of 100w rms components with low distortion. If you want it to power a pair of 250w subwoofers without any noticeable distortion you could bump up the supply voltage to 50v with a couple of cheap step up cuircets like this one.
$_57.JPG

Capable of up to 600w (max 10A input and output.)
Should run you maximum 20$ each.
You can easily turn the amplifier on and off with your head unit by using an SSR or a conventional relay.

This will be small and efficient using digital technology.


Ask if you have any questions :)
 
Running 12v amplifiers on a 24v system using converters are both very little efficient and hugely expensive.
Stay 24v on as many electrical component as possible.
I tried a 24v head unit for a while but couldn't find any good 24v units so I now run a 12v head unit with a converter, but everything else are 24v.
 
good thread, will revive, i also have this issue and all stepdowns are 30 amps max,

I figured 12V x 30amps = 360watts total Per step down.

Is this correct? I ignore all the marketing BS and like to stick to the actual consumption or rating. :-)
 
Back
Top Bottom