Recent content by JLB206

  1. JLB206

    What did you do to your pig today?

    The photo on the beach is with the 2.5” spring lift? In the back also? What size tires are you running? Mine with factory springs (as far as I can tell) has about the same clearance in the back with 33’s and I bottom out on occasion. Was thinking I needed the 2.5” lift, but…maybe the PO...
  2. JLB206

    Build Build Thread: Jim’s ‘55

    To be clear, I have been stopping great all along. It just developed this “pump it once, and THEN stop” situation this week. And I’m not arguing that it isn’t a big deal. I’m just not ready to throw everything out and start over just yet. I think replacing the one cylinder will resolve that...
  3. JLB206

    Build Build Thread: Jim’s ‘55

    That is a bigger task than I am ready to start. I still have the tranny and transfer case to rebuild! And then new shocks and springs, not to mention finalizing the AC, replacing the coolant hoses I cut up and coupled to make the new motor work, etc, etc, etc. Disc brakes are pretty far down...
  4. JLB206

    Build Build Thread: Jim’s ‘55

    Pulled all 4 drums and found a little of everything. 2 wheels in good shape. RL has sprung a leak in one wheel cylinder. Looks pretty recent as not everything is covered in fluid/no fluid coming out of the drum. That probably explains the change on Monday. Up front, I have a delaminated...
  5. JLB206

    Build Build Thread: Jim’s ‘55

    Well that isn’t what I want to hear. and I was just thinking about how well she was running! Back to whack-a-mole!
  6. JLB206

    Build Build Thread: Jim’s ‘55

    Alright, that is 3 votes for shoe adjustment. And it’s probably a good thing to get a look at the wear anyway- I haven’t looked at them since I purchase it last year- low on the priority list until stopping became an issue! Then immediately to the front of the list! Fun wheel related tidbit-...
  7. JLB206

    Build Build Thread: Jim’s ‘55

    Are you talking about inside the drums? Should I need to adjust the shoes? The brakes were in good working order before my engine swap, so all I did was bleed the air out of the supply lines going to the brakes when I put everything back together. And when I say “the brakes”, I mean all four...
  8. JLB206

    Build Build Thread: Jim’s ‘55

    It’s been a while since a proper update, and this isn’t that- I’ve got a brakes question: when I got her back on the road (late July), I installed a new brake master cylinder b/c the old one seemed to have failed and I couldn’t get great pressure. Now I’m 4 months into driving her and something...
  9. JLB206

    Build Build Thread: Jim’s ‘55

    Not really part of the “build”thread. Maybe it’s a “re-build” on this one. At some point since I brought her home in June ‘24, the passenger side shock absorber mount on the axle broke off. Noticed it this weekend, while putting on mufflers (finally!). Her are some before/during/after shots of...
  10. JLB206

    Build Build Thread: Jim’s ‘55

    I do have the cover for the bottom of the HVAC module which should clean up the exposed passenger side of it, but I think the whole dash is going to get looked at for a refresh. The only original items from the center section that are going to remain are the rear window up/down toggle and the...
  11. JLB206

    Build Build Thread: Jim’s ‘55

    All I did was flip the motor over and mount it to on the cabin side of the linkage rather than the firewall side. The linkage geometry is unchanged. I actually swapped in the Silverado wiper motor so I can have intermittent function as well. Also the original motor was weak AF! Not sure if...
  12. JLB206

    Build Build Thread: Jim’s ‘55

    Still sorting out the details, but I’ve done it: shoehorned the HVAC module from the Silverado into my 55. Had to modify the housing a bit to snug it up against the firewall and make room for the stick, and the passenger foot space isn’t what I would call “spacious,” or “open,” but it is...
  13. JLB206

    What did you do to your pig today?

    Mine came with one. Have not had any issues in over a year, but my drip rails are surprisingly not very rusty.
  14. JLB206

    Build Build Thread: Jim’s ‘55

    Forgot to attach photos. Can’t find photos of the tunnel right now. I want to ease the edges of the scoop a bit. Side by side with the factory details, the hood scoop angles are a bit too crisp. Time to experiment with my harbor freight metal brake. 2nd and 3rd pics are pre-welding. I...
  15. JLB206

    Build Build Thread: Jim’s ‘55

    I’m still putting things back together, and finding other things to take apart. First with the sheet metal: tunnel modification is 90%. I have one section to fill in, but for the most part, it is complete (enough). Cut the bolt flange off so I wouldn’t lose that alignment, then infilled the gap...
Back
Top Bottom