Recent content by HammyLumps

  1. H

    SOLD SF Bay Area - Wilco Hitchgate Solo High Clearance - $500

    **Local pick up only** Bought in March 2018; selling because my cruiser is going. $500 -Wilco Hitchgate Solo High Clearance -Custom license plate bracket (not wilco) -License plate wiring kit (not wilco) -Locking hitch pin
  2. H

    SOLD SF Bay Area - (5) 285/75R16 BFG All-Terrain K02's w/16in rims

    **Local pick-up only** **$700 OBO** These equate to 33 inch overall size. Rims came off my 1991 land cruiser and were on the vehicle when i bought it - no idea what they are from - but they are not stock LC wheels. Have lugs if you need them too. Spare tire is a different looking black 16...
  3. H

    Beach camping recommendations on Oregon coast?

    Has anyone done any wheeling and camping at Oregon Dunes National Recreation Area? Going to run the OBDR in August and was thinking of setting up camp there for a few days before heading out on route 6. Is it worth it? Seems like one of the few places on the OR coast you might be able to camp...
  4. H

    Wanted 80 series VSV for EGR

    Looking for a VSV for EGR in good working order (pn 90910-12079)
  5. H

    For Sale 80 Series passenger knuckle housing, birf, spindle [Bay Area]

    parts are used but in good condition. (1) passenger side knuckle housing w/ ABS sensor hole - $90 (1) birfield/CV - $80 (1) spindle - $40 or $190 if you take everything Prefer local sale
  6. H

    Wanted 80 Series Passenger Knuckle Housing

    Found one, so no longer needed.
  7. H

    For Sale 80 Series CV/Birfield

    Have 1 CV off a 1991 80 series (not a pair). Seems to be in good working order. I'm not sure how many miles are on it. I just needed the axle shaft this was attached to since I ordered new CV's. Message me if interested.
  8. H

    Wanted 80 Series Passenger Knuckle Housing

    Ideally located in California. If local to SF bay area, I can pick up otherwise I will need it shipped. Please let me know.
  9. H

    knuckle stud thread

    In the midst of front axle rebuild and found out the previous owner put in 2 bolts instead of replacing the knuckle studs. To make it worse, they were self-tapping bolts and totally stripped the threads in the knuckle. I was thinking of using a Heli-Coil thread repair kit to rethread the...
  10. H

    Front Axle Rebuild - For FAQ

    UPDATE - had to cut the star apart to get at the c clip. The c clip was very deformed and the reason it was so difficult to separate. The splines on the axle shaft were either already damaged from the previous s***ty install or from my attempts to separate it. I tried to file the splines to...
  11. H

    Front Axle Rebuild - For FAQ

    First time doing this...How far in should the new oil seal be driven? Flush with the top of the hub (as pictured) or in so it is flush with the surface of the rear bearing?
  12. H

    Front Axle Rebuild - For FAQ

    No, not original owner. I bought it with 230K miles a few months ago. I have no idea if the axle was ever rebuilt. Shortly after I bought it, it started spewing diff fluid out through the grease cap and all over the wheels, so I decided to do the rebuild. Now that I have it apart, I also...
  13. H

    Front Axle Rebuild - For FAQ

    They are in so tight, i'm chipping chunks of brass off the drift. Would heat help?
  14. H

    Front Axle Rebuild - For FAQ

    Are there any tips to knocking the races out if they are stuck? Tried to get some liquid wrench in there but that doesn't seem to be helping...
Back
Top Bottom