Recent content by fzj80crew

  1. F

    96 LC Stoker Kit and Turbo ECU/Tuning Advice

    So MOTEC referred us to Cody Phillips Racing. We contacted them and laid out our requirements: harness and tune, to include passing VA emissions. The good new is he did not say "No" but we did not get a firm yes. He is going to do some research and get back to us. So now we wait and hope that...
  2. F

    1996 FZJ80 Backcountry and Overlanding Build

    The costing will vary based on what you want to have done to it and the products that you use. I would suggest finding a couple of shops, discuss what you want, and get quotes when you are ready. We are trying to keep it OEM where we can but it will not be pure due to our design for its new...
  3. F

    1996 FZJ80 Backcountry and Overlanding Build

    We are working with Off Road Innovations in Winchester, VA. Chris Lockridge (owner) and John Robinson (Chief Operating Officer) are great to work with. We brought them our design and continue to work closely with them on the build. The work posted above was done over a couple of months. The...
  4. F

    1996 FZJ80 Backcountry and Overlanding Build

    Once the underside of the body was media blasted any remaining rust was mechanically removed. All the seam seals were repaired using commercial grade seam seal and then POR15 was added. Below are pre-media blast and post POR15 pictures.
  5. F

    1996 FZJ80 Backcountry and Overlanding Build

    Renago thanks. We hope so. To treat the rust on the frame we decided to have it sandblasted and re-powdercoated to prep it for POR15 rust prevention coating and Eastwood's "Internal Frame Coating". You can see the divots in the frame where the rust was getting started. That said we are...
  6. F

    96 LC Stoker Kit and Turbo ECU/Tuning Advice

    We have reached out to John Reed Racing and are waiting to hear back. Emailing Jay Meagher at Real Street Performance and HALTECH when I get off work tomorrow. White Stripe: We have both types of emission testing-one you can register on line and drive by and the other type if you go to a...
  7. F

    1996 FZJ80 Backcountry and Overlanding Build

    We had the underside of the body mobile media blasted to to remove the rust and clean it to be treated with POR15 rust preventative.
  8. F

    1996 FZJ80 Backcountry and Overlanding Build

    ORI in Winchester had done two JK builds for us so we went with them for our overloading project. The first thing we did was start tearing it down to evaluate everything. Here is the body separated from the frame. We were surprised at how much rust was on the top of the frame and hidden by the...
  9. F

    1996 FZJ80 Backcountry and Overlanding Build

    We’re writing this thread to share our observations and lessons learned as we repair and outfit an 1996 FZJ80. It will be used for overlanding after we retire and to do backcountry trips. Here are the pictures of it when we purchased it.
  10. F

    96 LC Stoker Kit and Turbo ECU/Tuning Advice

    All, Thank you for the continued advice and information. The stroker kit is a done deal so no changing my mind about that but the turbo has not been ordered. So the two phased approach ,until I do not have to get it through emissions, looks like it might be the best option unless one of the...
  11. F

    96 LC Stoker Kit and Turbo ECU/Tuning Advice

    Many thanks for your response. What turbo would you recommend? We were shooting for less lag time to spool up. I know the emissions thing is going to make it a lot more complicated but in a couple of years it will not have to do emissions so.. Also we were not looking to tune this build to...
  12. F

    96 LC Stoker Kit and Turbo ECU/Tuning Advice

    I am working with ORI Winchester to build a 96 Land Cruiser overlanding vehicle for North American trips. I looking for and would welcome any recommendations on ECUs (Haltech or Motec) and someone/company that can build a wiring harness and do a tune/program that will pass VA emissions. Also...
Back
Top Bottom