Recent content by BelgianHJ60

  1. BelgianHJ60

    A Belgian HJ60 restoration progress

    Tried my hand at painting the inner door jams, just so I can fit the doors already. Did the hinges and some bits and pieces. Plastic wire loom covers and heating vents were resprayed, as well as the backseat heater. Applied butyl sound deadening on the floor to cover around 40-50% of surface as...
  2. BelgianHJ60

    A Belgian HJ60 restoration progress

    Some more pics after sandblasting some panels. Removed quite a bit of surface rust. Then epoxy primed. The inside of the fenders and hood will be raptor lined. All the 'outer parts' will be primed and prepped by me, but will let someone else spray paint it as my setup isn't ideal. Also, really...
  3. BelgianHJ60

    What is this part?

    I think it might be 85550-90A00, resistor assy, pilot lamp. No idea what it does.
  4. BelgianHJ60

    What is this part?

    What is this part? What can I replace it with? No part number legible. It's mounted on my left fender, closer to the firewall than the voltage regulator. 1984 LHD HJ60. Additionally, the voltage regulator is mounted close, but attached to the same mounting point is a small electrical thingy...
  5. BelgianHJ60

    SEM products for interior restoration - NLA in Europe?

    Would changing every part to the non-OEM Cordovan Brown by SEM be an option? Seems that SEM quality is the way to go and not sure that custom paint would be as good quality... Any feedback on the other SEM colors I proposed?
  6. BelgianHJ60

    SEM products for interior restoration - NLA in Europe?

    Hi all, As I'm advancing through my 1984 HJ60 restoration, the interior really needs a touch-up. Pretty all the threads here lead to the SEM product catalog, which has proven results. These products are however very hard to source in Europe. Multiple suppliers have cited "excessive...
  7. BelgianHJ60

    Intro + Slow and steady upgrades

    Great looking Cruiser, hope to arrive there someday myself!
  8. BelgianHJ60

    A Belgian HJ60 restoration progress

    This is what the underside of the car looks like right now. Raptor lined the undercarriage and tinted it in the right colour. Brake lines are as good as in place. Fitted a brand new fuel tank with new straps as well, which was kind of a pain to get to fit. Those who know their 60 will notice I...
  9. BelgianHJ60

    A Belgian HJ60 restoration progress

    Body is back on the frame, engine and gearbox too. Slowly building up the car again and trying to finish up one system at a time. Next up is the power steering. Already have the parts, but need to have some connections pressed. Most of the stuff is NLA from Toyota, so have to improvise.
  10. BelgianHJ60

    A Belgian HJ60 restoration progress

    Also went ahead and gave the alternator a good clean-up. 24V (40amp?) with the vacuum pump on the back. I soldered in new brushes (or at least made a valiant effort with the POS soldering iron I have) and installed some new bearings. Aluminium parts were waterblasted, the rest was painted. I am...
  11. BelgianHJ60

    A Belgian HJ60 restoration progress

    Was about time to make the engine look a little less... crusty. Painted everything i possibly could. Will attach fuel lines and headers when it's back on the chassis. New glow plugs, new sensors, new valve cover gasket, new filters, new belts, new clutch, new engine mounts. Also new waterpump...
  12. BelgianHJ60

    A Belgian HJ60 restoration progress

    Going to start uploading more progress. Have not been at it for a while due to work and house renovations. Welding the holes in the underbody proved to be really difficult/impossible to do properly with all the rust still there. Rented a sandblaster and went at it. Afterwards put a first coat...
  13. BelgianHJ60

    Where does this part belong?

    So nearly two years go I pulled this off my HJ60. I stuffed this away and labeled it "transmission - support plate". Cannot figure out where this goes back, anyone who knows or has a pic of their own? 1984 HJ60, 2H, H55F
  14. BelgianHJ60

    I ****ed up - advice needed - sand in motor

    Thought so, i did not turn it over yet so hopefully I can clean it without pulling the cam. Just from the oil pan removed, svould give me access i think
  15. BelgianHJ60

    I ****ed up - advice needed - sand in motor

    It is a good running engine, where do those channels go to? do they go directly to the sump? Am i right that an oil filter will in fact catch these grains of sand? they are 50-70 µm.
Back
Top Bottom