Search results for query: *

Forum search Google search

  1. Output Shaft

    Another FJ60 hesitation/stutter/hard to start when warm thread

    If the fuel cut solenoid functions with a hot wire (bypassing the emissions computer) but won't activate when hooked up normally, my guess is either the plug at the carb is whacked or the emissions computer's FCS circuit is FUBAR. The only way to rule out the emissions computer is to find...
  2. Output Shaft

    Overflow tank never changes...

    If the coolant level in the radiator expansion tank doesn't start to rise within 10 minutes after starting the engine... or lower a few hours after shutting down the engine, the radiator cap is faulty. The cooling system will be overpressurized when the engine is running if the cap doesn't...
  3. Output Shaft

    Fast Idle Speed Adjustment - Fan Clutch Free or Locked?

    Free?
  4. Output Shaft

    PSA: Harmonic Balancer

    DamperDoctor Harmonic Balancer Rebuilding/ Repair at Dale Manufacturing (for others stumbling onto this thread)
  5. Output Shaft

    H55 Over-run "Humm"

    Who installed it? It's possible that the input shaft got cram fit into the pilot bearing during installation resulting in excessive axial force pressing it rewards on the front bearing. We also don't know if it was installed without a mishap. It's really easy to tweak the front bearing alignment...
  6. Output Shaft

    H55 Over-run "Humm"

    New h55s don't blow up their front bearings. What happens when the truck is idling & you push in the clutch? Any weird sounds?
  7. Output Shaft

    PSA: Harmonic Balancer

    Holy crap! Yeah.... Definitely I'm gunna crawl under the front of the car and twist that nut by hand (fingers) just to make sure it's not loose... occasionally now too. I had mine off a couple years ago to change the cover gasket, and I guess there's no guarantee its gunna stay put even though...
  8. Output Shaft

    H55 Over-run "Humm"

    It will never leak externally. It can leak internally into the transfer case. Check the transfer case oil level too.
  9. Output Shaft

    '83 FJ60 won't start....HELP!

    I assume you mean you cranked the starter at least 5 revolutions, not just turned the ignition key to ON.
  10. Output Shaft

    Low vacuum and compression?

    Both compression and vacuum will be lower at 9000 ft because the air is thinner. Check it at 4000 ft or lower. But 105 psi compression is low. Any old 2F at 9000 ft (especially one that spits oil & blows blue smoke) with 33 inch tires and stock 3:70 differential gears is going to have the...
  11. Output Shaft

    H55F stuck in first gear

    That's definitely not the H55F. I don't know what it is. Maybe check in at a Land Rover or Nissan forum.
  12. Output Shaft

    Fuel Gauge & Wiring Testing

    The Body manual has troubleshooting procedures.
  13. Output Shaft

    Bearing grease

    I would recommend just using one grease for everything. That way there's only one grease gun and you only need to have one type. You can't go wrong with using that Valvoline SynPower Grease mentioned above for everything.
  14. Output Shaft

    Bearing grease

    Mobil 1 red synthetic grease is an amazing EP lubricant. I once did an (unscientific) test with it comparing it to that molygraph stuff I mentioned above. I had two aluminium tubes that could barely fit inside each other. They would bind when pushing & turning them to try to insert one into the...
  15. Output Shaft

    FJ60 Brake Problem - bleeding master

    Assuming that the brake pedal was firm before the caliper & hose-to-caliper upgrade, the master cylinder & booster would not have changed for the worse. Since you mentioned that it was difficult to get the fronts bubble free, that's pointing to air not getting purged completely. The speed...
  16. Output Shaft

    H55F stuck in first gear

    This thread has some info. Not necessarily what's going on with your transmission. h55f stuck in gear
  17. Output Shaft

    Bearing grease

    Don't use the red Mobil 1 synthetic grease in the birfields. It is an awesome wheel bearing grease though. If I was going to completely clean out the birfield joints & repack the joint & repack the wheel bearings, I think you'll need at least 2 tubes of grease. You won't need four (per side)...
  18. Output Shaft

    1985 FJ60 fuel tank hoses

    If you've got the part numbers, any Toyota dealership.
  19. Output Shaft

    Paint for manual locking hubs.

    Those hub parts don't get hot. High heat paint isn't necessary.
  20. Output Shaft

    Bearing grease

    Back in the day... There wasn't much to choose from 30 years ago, and (me being a one grease kinda guy) used Sta-Lube Moly Graph Extreme Pressure grease for 28 years... For everything. Moly-Graph® Extreme Pressure Multi-Purpose Lithium Grease, 14 Wt Oz And I can't say that I've ever had a...
Back
Top Bottom