Search results for query: *

  • Users: TEC3
  • Order by date

Forum search Google search

  1. TEC3

    For Sale  Overland Built 100 Series Tennessee USA

    We are selling out 2006 Toyota Land Cruiser recently built for Overland/ Off Road Travel. This vehicle has been built well with only high end parts. You need nothing to hit the trail or travel. Recently just drove to Idaho and back with no issues. Tent and Awning can be negotiated, but are not...
  2. TEC3

    Can someone with 315’s do a fender measurement?

    Lol, I know. And yes I would be lifting from frame to allow travel of the suspension I do need to find extended bump stops front and rear to limit up travel if you have suggestions there.
  3. TEC3

    Can someone with 315’s do a fender measurement?

    Care to check shipping to 37760?
  4. TEC3

    Can someone with 315’s do a fender measurement?

    Just so I make sure sure I’m measuring correctly. On ground I’m center hub to fender well, then put on a jack, lift until tire leaves ground and measure the same measurement?
  5. TEC3

    Can someone with 315’s do a fender measurement?

    Looking as we type for a sway bar, not sure why they didn’t correct the issue instead of cutting it to clear the drive shaft. They pulled mounts, end links, everything. 2. I need to see if I have a fire stone locally. Small town. 3. I cut and hammered the pinch weld flat, but may do more. I...
  6. TEC3

    Can someone with 315’s do a fender measurement?

    And you mean 60-70mm right? So roughly 2-2.5” of Down travel?
  7. TEC3

    Can someone with 315’s do a fender measurement?

    Right, I’m sitting at 22.5 and do not have rubbing with 315’s. Need to measure my down travel. Wanting to drop a little more to eliminate the last bits of some Torque steer. Long story short had a shop do my lift, they cranked it to 24.5, ate CV’s while driving cross country, had horrible...
  8. TEC3

    Can someone with 315’s do a fender measurement?

    Could someone with 315’s(35’s) measure from center hub to fender well on both front fenders? We are back from a trip and I think my Torsion bars still need to be adjusted down. Thanks, Tommy
  9. TEC3

    @Ayunes Overhead mount for ScanGauge. Excellent.

    Was looking at scan gauges today. This is slick. How can we order the Mount? @Ayune ?
  10. TEC3

    How to ID which wheel speed sensor is failing?

    W Will do. I am doing some research on the best one. Was considering a scan gauge so I could watch trans temps but can’t get a clear answer on if it can read those codes. Also I see on here that some people have had issues with 100’s and scan gauge.
  11. TEC3

    How to ID which wheel speed sensor is failing?

    Don’t mind to do that. My scanner doesn’t read the VSC codes, just CEL codes. A suggestion on a quality code reader that will do that would be awesome.
  12. TEC3

    How to ID which wheel speed sensor is failing?

    I have a Bluetooth code reader, but for some reason it isn’t reading anything except CEL codes. Would you care to share the one you have that will read ABS/ sensor codes?
  13. TEC3

    How to ID which wheel speed sensor is failing?

    VSC/ TRAC light and VSC off light. It’s intermittent, but most common on longer drives. I understand the lights can mean a few things. But my question is the same, is there a good way to read the codes being thrown without going to a dealership?
  14. TEC3

    How to ID which wheel speed sensor is failing?

    Recently I am getting VSC and TRAC lights randomly. Mainly during highway driving. I assume I have a wheel speed sensor going out. Next time it happens I’d like to try and diagnose which sensor is failing. Any way to do that without going to the dealer? Since it’s intermittently failing it...
  15. TEC3

    Torque steer after lift

    Thanks guys, Spent this morning working on it. I’m currently across country in idaho (from TN) and think I found some of the issue. A hub measurement from center to fender on pass side turned out to be 24.25 while the driver side(toyota lean) was 22.5 I leveled the truck side to side in the...
  16. TEC3

    Torque steer after lift

    hey guys, Searched and found a few good reads on torsion bar adjustment and the appearance of torque steer. But had a few specific questions. 06 cruiser, new suspension running 315’s(35’s) It wanders a little, but mainly notice torque steer on acceleration and deceleration. It’s so bad I don’t...
  17. TEC3

    Randomly Died and wouldn't start

    I got the part numbers for both and got OEM ones ordered. both were available on amazon prime so I should have them saturday for the swap. Once they come in ill post a follow up so people know what to order for the varying years.
  18. TEC3

    Randomly Died and wouldn't start

    So it appears that it has 2? And 2006 is a Cut year so 1/2 the year used one style and 1/2 used the newer style. I’m going to crawl under there tomorrow and get the actual part number so I don’t order the wrong thing
  19. TEC3

    Randomly Died and wouldn't start

    Good info and probably my plan of action. I replaced the fuel filter and gas cap with OEM ones. They were cheap and at the mileage worth changing. I will order the purge valve. At some point it will be a whole new fuel system lol
  20. TEC3

    Randomly Died and wouldn't start

    Thanks, Did yours start right back up or did you have to wait? Mine takes time and will not start without purging fuel line pressure
Back
Top Bottom