WTB FJ80 Tailgate Handle

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Pictures of wrench installed? Or do you use the wrench to turn the actuator?
 
I missed this original thread and that would be a nice upgrade. I just noticed a hairline crack on my handle a while back and I suspect I'm not the only one. Send SoCal a pm and let us know what you find out.
 
I will have to take a pic this afternoon of the wrench installed as the handle.

Please do - I have the same truck and the same problem. Wrapped the two exposed steel legs with duct tape as my temporary fix so your wrench sounds a lot better than my hack - thx!
 
image-2072204092.webp

There you go

Sent from my iPhone using magic

image-2072204092.webp
 
Tailgate Handle

I need to replace the plastic door latch on my lower rear tailgate (the black plastic handle that has a splined receiver for the latch post). I'm guessing these break all the time? Anyone have one for sale? If cruiserdan is listening, can I order them through you?
Thanks to all in advance

I replaced mine with a manual window handle. you will need to remove the knob so the top half will close. it works great. been on for 8 yrs.
 
I like it! Thx for the pic...
 
I know other people have made these in the past, but mine recently broke so I made some.
Made from aerospace grade aluminum, anodized red or black. I have some engraved "Landcruiser" and some blank. I have them listed at $45.00 each. You can DM me here or buy them on ebay.
I can custom engrave the blank ones for an additional $20. Keep in mind there's not much room there to engrave so save your inspirational quote for somewhere else. Does not include the screw. Photos below, Cheers!
s-l1600.jpg
s-l1600.jpg
s-l1600.jpg
s-l1600.jpg
 
I know other people have made these in the past, but mine recently broke so I made some.
Made from aerospace grade aluminum, anodized red or black. I have some engraved "Landcruiser" and some blank. I have them listed at $45.00 each. You can DM me here or buy them on ebay.
I can custom engrave the blank ones for an additional $20. Keep in mind there's not much room there to engrave so save your inspirational quote for somewhere else. Does not include the screw. Photos below, Cheers!
s-l1600.jpg
s-l1600.jpg
s-l1600.jpg
s-l1600.jpg
Chris, can you send me your link for the listing on ebay?
 
I know other people have made these in the past, but mine recently broke so I made some.
Made from aerospace grade aluminum, anodized red or black. I have some engraved "Landcruiser" and some blank. I have them listed at $45.00 each. You can DM me here or buy them on ebay.
I can custom engrave the blank ones for an additional $20. Keep in mind there's not much room there to engrave so save your inspirational quote for somewhere else. Does not include the screw. Photos below, Cheers!

Hey aren't chance you have any of these still? If you do id take one. PM'd you
 
I know other people have made these in the past, but mine recently broke so I made some.
Made from aerospace grade aluminum, anodized red or black. I have some engraved "Landcruiser" and some blank. I have them listed at $45.00 each. You can DM me here or buy them on ebay.
I can custom engrave the blank ones for an additional $20. Keep in mind there's not much room there to engrave so save your inspirational quote for somewhere else. Does not include the screw. Photos below, Cheers!
s-l1600.jpg
s-l1600.jpg
s-l1600.jpg
s-l1600.jpg
bumping this up again, still have a few left, DM to order
THANKS!!
 
Still available new from Toyota.

Those custom machined handles are sweet. For those who want OEM though,

8FA8F612-C8E5-4C3C-AA34-2AD0A36AECE2.jpeg


FYI it’s the same as the 70-series back door handle. The bushings and hardware is still available too.

Cheers
 
Last edited:
Back
Top Bottom