Window Noise

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I've found the wind noise on mine occurs at relatively low speeds (30-35 mph). I think I may tape off different areas of the window one at a time to confirm the exact source of the noise. Mine is predominantly from the pass. side so it's hard to tell what's going on from the driver's seat. Could always test drive it with a helper too I suppose. :rolleyes:
 
Hmm, Glass does wobble just a little when I tested it. I did notice that when running the windows up and watching from the outside that the bottom of the glass physically pushes the edge of the door on the outside at the bottom of the glass out with a noticable bow when it is in the position that makes wind noise.
 
Hmm, Glass does wobble just a little when I tested it. I did notice that when running the windows up and watching from the outside that the bottom of the glass physically pushes the edge of the door on the outside at the bottom of the glass out with a noticable bow when it is in the position that makes wind noise.

If your glass wobbles on the way up, you need new window run channels fron CDan. The fuzzy stuff on the inside deteriorates and then the channel itself wears out leaving slack in the side to side movement of the window. If you live in a cold/wet environment your window will get slow and eventually pop out of the regulator at the bottom. You can adjust the angle that the window rises at, but if you have play in the channels it doesn't help much. As I recall the channels weren't too much $$ and not too hard to install.
 
Slow windows

. . . If you live in a cold/wet environment your window will get slow and eventually pop out of the regulator at the bottom.

I don't have any more road / wind noise than I did when I bought the truck new in '96, but I've watched this thread figuring my time would come.

However, after reading bearcat's note above, maybe I already have a problem and just don't know it. It does get "cool" here in the winter (nothing like the Wisconsin days though) and pretty wet. My windows are very, very, very, slow (so much I avoid opening them unless absolutely necessary). Does this mean I have a problem and need to replace some parts before my window glass pops out?

I always figured the motor was just wearing with age and there was nothing I could do but replace the motor when it died (I figured it was pricey).
 
If your windows are slow when its wet it's because the friction of the wet rubber combined with the channels being loose is too much for the motor to over come. Eventually you get one of two outcomes, either the motor can't move it back up after you roll it down, or it pops out of the regulator on the way down, which never happens in your driveway, but at least 50 miles from home in the rain. Replace the channels and you should be good. In the meantime avoid rolling your windows down in the cold or rain. I've done the drivers side but not the passenger, so I keep the passenger side locked to prevent my 11 year old son/fishing buddy from rolling it down.
 
I get the same thing from my sunroof. I push it up a tad and the noise goes away. I suspect the weather striping is shot. However, it sounds like you have mechanic problems also with the way your window goes up.

I just noticed this problem in mine. But I am thinking some moisture froze in the sunroof overnight and made a little gap. The problem seemed to subside on its own.
 
If your windows are slow when its wet it's because the friction of the wet rubber combined with the channels being loose is too much for the motor to over come. [SNIP].

Mine are slow pretty much all the time - wet, dry, cold, warm, always.

I think the channels are probably still the culprit - and certainly cheaper initial fix than the window motors that my dealer suggested. I'll give it a try when it gets warmer in a few months.

Thanks for the help!
 
Finally pulled the belt molding off on my RF door today and performed the repair from the TSB. What a difference, the annoying whistle I had before is now completely gone. I would recommend that anyone with a tough to track down wind noise give this a shot. I felt sure the source of the noise was higher up towards the top of the window, turns out I was wrong. Thanks again for posting the scan of the TSB. :cheers:
 
Well, after 5 years - I finally got around to it and tried the trick in the TSB. The noise is now gone.
 
Re-opening old thread...I did the TSB last weekend and still have the noise (put in new belt mouldings with the extra foam). My noise seems to come from B pillar, where the window meets, any ideas what it might be or how to correct? (I already replaced the window rubbers too).

Thanks
 
Yes,
Re-opening old thread...I did the TSB last weekend and still have the noise (put in new belt mouldings with the extra foam). My noise seems to come from B pillar, where the window meets, any ideas what it might be or how to correct? (I already replaced the window rubbers too).

Thanks

Yes, I fixed that on two rigs. It's unrelated to the mentioned TSB and belt moulding fix. Essentially, I pulled the window run moulding down and put some very thin felt tape at the upper corner of the moulding and reinstalled. It completely solved the wind noise coming from the upper rear corner of the drivers and passenger doors. I will grab a pic at some point today and post back. BTW - I chased that noise for a very long time.
 
You can see where I added a bit of cloth tape. This helps it squeeze the glass just a bit more. I found it solved about 90-95% of the wind noise coming from that corner, especially in cold weather.

Tape like this - Amazon product ASIN B00XPBB6L8
IMG_5264.webp


I have done this two rigs and it helped both quite a bit.
 
You can see where I added a bit of cloth tape. This helps it squeeze the glass just a bit more. I found it solved about 90-95% of the wind noise coming from that corner, especially in cold weather.

Tape like this - Amazon product ASIN B00XPBB6L8
View attachment 2143841

I have done this two rigs and it helped both quite a bit.
Did you get the same brand of tape? I bought the exact Tesa tape and it doesn't stick to the rubbers at all.
 
Did you get the same brand of tape? I bought the exact Tesa tape and it doesn't stick to the rubbers at all.

I don't remember, but I think so. I would have cleaned the rubber with acetone prior to applying the tape though. Sometimes heating up the tape a bit with a heat gun will help activate the adhesive more too.
 
I am definitely going to try the TSB and the channel corner fix.

My window is also slow especially in cold weather. Where can I source new channels?
 
Back
Top Bottom