Window Noise

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 9, 2004
Threads
131
Messages
610
Anyone else get wind noise through their front windows? 1995 super clean FZJ80. I've noticed that if I back the windows down a hair up front they become quiet as can be.

I've also noticed that when running the windows all the way up, they seem to tilt back at the very top and you can actually see the window frame tighten up against the side of the truck.

Do I need to adjust something or what?
 
I get the same thing from my sunroof. I push it up a tad and the noise goes away. I suspect the weather striping is shot. However, it sounds like you have mechanic problems also with the way your window goes up.
 
It is a known issue. PM with you email address and I'll email you the TSB.
 
Cruiser804- why not just post up the text of the TSB here for future reference for the rest of us?
 
PM sent
 
Cruiser804- why not just post up the text of the TSB here for future reference for the rest of us?

2X... I don't have this problem on either truck, but with 2, all potential issues seem to just be a matter of time.
 
I'd like to know as well. I just saw the TSB that has the tape but doesn't say where to put it.
 
I have a problem with the drivers side rear window not sealing, I think it is the window frame or the seal but the seal looks to be in good condition..
Any Idea's?
 
As I recall the TSB's for window noise are not very specific, i.e. put some foam tape on the door jamb until it stops. If you need to replace window runs it is not hard, just time consuming. Dan can get them for you for not too many bones.
 
MAY 24, 1996
BODY
BO007–96
L–C
FRONT DOOR BELT MOLDING WIND NOISE Page 1 of 2
To prevent a high pitch wind flutter noise caused by air rushing between the front door belt
molding and outer door skin area, foam–backed tape has been added to the back side of the
molding.
PRODUCTION EFFECTIVE:
Starting VIN: FZJ80–0119754
FIELD–FIX METHOD:
. Lower door glass to bottom of travel.
. Remove “Lower Frame Bracket Garnish”
(triangular plastic screw cover plate
located inside the vehicle at base of
mirror).
. Remove the 3 mirror attaching screws
and carefully pull mirror away from door
frame.
NOTE: Wrap door mirror with a shop towel
and carefully drape door mirror
against door.
. Remove belt molding attaching screw
(located at rear inside edge of door
frame).
. Grasp molding with 2 hands and pull
molding straight up using a swift upward
motion.
. Use needle–nose pliers to remove plastic
attaching clips that remained attached to
metal door panel when molding was removed.
Molding
Lower Frame
Bracket Garnish
Mirror Attaching
Screws
Outside Rear
View Mirror

FRONT DOOR BELT MOLDING WIND NOISE
FIELD–FIX METHOD (CONT’D):
. Reinstall plastic attaching clips to back of belt
molding.
NOTE: Place clips in the factory location.
Original location is easily determined
by the small scratch marks left on the
back side of the molding by the clips.
. Cover a work bench with a shop blanket and
place the molding facedown on the blanket.
. Center and adhere a piece of foam backed
tape (from the Toyota Squeak and Rattle Kit,
P/N 08231–00801) to the back side of the
molding, directly over the third clip (3rd clip
counting from the front edge of the molding).
NOTE: Tape should be approximately 10 mm
wide X 7 mm thick X 200 mm long.
. Reinstall belt molding (be sure that all
attaching clips are properly lined–up with
corresponding holes in the door panel before
attempting to install the molding).
. Install screw at rear edge of belt molding.
. Install outside mirror to body with 3 attaching
screws and snap lower frame bracket
garnish (triangular plastic mirror base) back
into place.
. Road test vehicle to confirm elimination of
wind noise condition.
WARRANTY INFORMATION: *
Page 2 of 2
Molding Clip
200mm
3rd Molding
Clip
Molding
10mm
7mm
Clip
OPCODE DESCRIPTION TIME OPN T1 T2
751371
R&R front door belt molding
(one side) including adding foam
backed tape
0.4
67111–602XX (RH)
67112–602XX (LH)
91 55
* In the event that both front moldings require this procedure, use “Z” time for repair of
opposite side. Please refer to the Toyota Warranty Policy and Procedures Manual,
Policy 8–14 for additional details.
 
No sure how else to post this. It is a PDF so the formatting and illustrations are lost when converted to text.

I don't know how to convert a PDF to jpeg and even then it would prolly be too big to post.

Suggestions?
 
You could take screen shots of the PDF pages, paste them into MS Paint, save as JPG files, then upload them to photobucket. Email the PDF file to me and I'll be more than happy to do it. Either way, thanks for posting this, I have somewhat of an idea of what the fix involves now.
 
Great thread. I would love to see some illustrations. I have the wind noise on both doors.
 
Not sure how these will come out
Window TSB1.webp
Window TSB2.webp
 
Huh, my noise seems to come from the top of the window and changes if I back the window down just a hair from all the way up, yet still showing that it is not open. I wonder if I need to adjust the window tracks as it seem the top of the glass slopes towards the front of the vehicle and then rotatates to level as it reaches it's mechanical limits in the up position.
 
Huh, my noise seems to come from the top of the window and changes if I back the window down just a hair from all the way up, yet still showing that it is not open. I wonder if I need to adjust the window tracks as it seem the top of the glass slopes towards the front of the vehicle and then rotatates to level as it reaches it's mechanical limits in the up position.

You may have a different problem. The glass may be coming out of the metal channel / rubber seal that it sits in on a mechanism with a wheel track. It runs the length of the bottom edge of the glass. If the glass leaves this channel or shifts in it, there can be what you just described.

The easiest way to find out is to pull up on the glass and see if it comes up in your hands / shifts on one end (likely back end). Don't do this unless you're planning on fixing it that moment as it could litterally come off in your hands and leave you there holding the glass wondering what to do next. Have a plastic C wood clamp handy and you can pull the glass to the top of the channel and clamp over the window frame to hold it in place.

Then follow the FSM to remove the inner door trim, open the plastic, pull the rubber from the channel, clean the dirt out of it that causes this issue in the first place, clean the rubber mounting strip, then re-seat everything. Putting it back together can be a challenge. Dish soap can lubricate it so you can reassemble it, but doesn't make a good adhesive. Someone else may have a good suggestion on what to use or it may be in the FSM.

Don't forget to remove the tiny screw on the door opening mechanism trim before removing the interior trim panel. Yes, I broke one.
 
Huh, my noise seems to come from the top of the window and changes if I back the window down just a hair from all the way up, yet still showing that it is not open. I wonder if I need to adjust the window tracks as it seem the top of the glass slopes towards the front of the vehicle and then rotatates to level as it reaches it's mechanical limits in the up position.

I have this problem. It is why I looked at the thread. But I always blamed it on PO's rollover and straightening the upper door frame. I haven't worked on it yet because it only bothers me on the highway and it's hard to fix anything at 65MPH!
Most Jap cars you remove the inside panel and adjust the window regulator tracks to move the closed glass toward the area that whistles. Check for smooth movement and road test at the speed that the whistle occurs. When the noise is gone, put the door panel back on.:)
 
Back
Top Bottom