Will's '96 LX450 Project Thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 31, 2015
Threads
11
Messages
103
Location
Memphis, TN
Been a long time lurker on the forum and now that I am officially the owner of a '96 LX450, I figured it was time to join and start a build thread.

My father and I have always been fans of the 80 series. A coupe years ago I built a 1500 Silverado but found it to be way too cumbersome for most trails. The IFS in front was always a failure waiting to happen as well.

I made the decision that an 80 would be the perfect fit as the "outdoors truck to end them all"... There is not much that I enjoy more than camping, fishing, and spending time outdoors.

On to the 80 - I picked up this 1996 LX450 last week with 158k and a very straight body (minus a crooked front bumper). Overall it runs fantastic with only a few minor issues. It is leaking some oil from the front of the block. Haven't had a chance to figure out if it is an oil pan gasket/distributor gasket or who knows what yet. That will be addressed soon. The front seats are cracked and I have new leather coverking covers on the way for them. She also needs some brake attention and a new A/C compressor. All things on the "fix list"...

But the good stuff:
I've already bought an ARB front bumper and a Warn 10,000lb winch. In time, I plan to get around to the following additions:
-OME Lift / 35" BFGs
-Roof Rack + Roof Top Tent
-Slee rear bumper + Tire carrier
-Rock sliders
-Rear storage drawers + camping provisions


 
Last edited:
I'm getting ready to replace the oil pan gasket. Called my local Toyota dealer and they claim that Toyota does not make an actual gasket for the FZ anymore and recommends using RTV. Is this correct? I think I'd rather have a real gasket.
 
Most likely your problem(s) is:
Oil pump seal
Front main Seal
Distributor O-Ring gasket
Valve Cover gasket
Spark Plug Tube seals (inside Valve cover)
Power Steering hoses

After these, you can look at the oil pans and using the FIPG.
 
Thanks for the help guys... I was hoping the front main wouldn't be brought up... :eek:

Leak definitely seems to be coming from up front. I need to get the area thoroughly degreased so I can get a good look at where it is coming from but it doesn't seem like it is high on the block.
 
Nice cruiser, welcome to the addiction, now the fun begins!
 
Alright PLEASE forgive my ignorance on this one. I have many hours of experience working on '50's Chevys but not much on "newer" vehicles.

I degreased the entire engine yesterday and can see pretty clearly where oil is and isn't on the block. At first glance it seems like the profuse leak is coming from a cooling line at the front driver's side just behind the radiator. Primarily where the rubber hose splices into steel line. Is there an "oil cooler" in this vehicle? I'm definitely leaking oil and not trans fluid.

Nice cruiser, welcome to the addiction, now the fun begins!

Thank you!
 
The front main and oil pump gasket are much easier to redo then the oil pans. There is no external oil cooler on this vehicle, only power steering and transmission. The actual oil cooler sits under the exhaust manifold. You are losing oil from your oil pump, front main, valve cover, or distributor o-ring. It is then probably blowing back across the pans and over the transmission. Lots of experience with this ;)

Also, on your bumper selection, you might consider a 4x4 labs. It will be a lot cheaper than an ARB. Gives you a much better departure angle then the ARB ever will, and looks sweet doing it.
 
Thanks for the advice guys. Top of the block is very dry so I'm betting that it is the oil pump gasket or front main. I'm going to give the oil pump gasket replacement a go this week hopefully and take it from there.

And I actually already have the ARB bumper on order, supposed to show up later this week.

But while I'm waiting on parts I did a couple small things (aside from getting my a/c working :))

Recovered my very cracked armrest with some vinyl. Not a great match but the whole thing cost $8 and feels alot better on my arm! Also added a CB. Antenna will be mounted on the ARB bumper.



Installed a KC Cyclone light as the underhood lamp. Decent flood over the engine compartment. Oh yeah, that duct-tape intake hose repair... new hose in on order.



Lots of boring stuff for now.. hang in there.
 
Side note, does anyone know where I might be able to find the cover that goes over the spark plugs wires on the valve cover? Don't mind if it is Toyota or Lexus
 
I have the same LX. I'll be watching.
 
Side note, does anyone know where I might be able to find the cover that goes over the spark plugs wires on the valve cover? Don't mind if it is Toyota or Lexus
Welcome.
Just watch out for people parting out 80s for the spark plug wire cover.
 
Thanks for the pointers, guys. I'm so used to working on 1930-1950's area vehicles that I still haven't gotten in through my head yet that I can go to the dealer for parts....

The LX got a little facelift today! I was able to install the newly acquired ARB bumper along with a Warn 10,000lb VR winch and some ProComp 7" HID lights. I am really digging the whole setup so far! This one put a good dent in my wallet but it sure makes me want to get moving along to the lift and new wheels/tires.

In other news, I replaced the power antenna mast, got an OEM lock remote programmed, and picked up a new oil pump seal and crankshaft seal from the Toyota dealer.

Here are some pictures from today's work. If you're wondering where the marker lights are, I managed to run over the box that contained them in my garage. :doh: ....replacements have been ordered. Also forgive the wonky shackle situation.. it seemed like a handy storage location for them at the time. :lol:


 
The LX started running like a dog at idle.

A quick inspection revealed the plugs and wires to be originals. I replaced the plugs, wires, dizzy cap and rotor. Runs like new now.

However when I was replacing the plugs I climbed in and out of the engine compartment a couple times. Now my radiator leaks and I can't figure out where from. What did I do?.... :bang:
 
The LX started running like a dog at idle.

A quick inspection revealed the plugs and wires to be originals. I replaced the plugs, wires, dizzy cap and rotor. Runs like new now.

However when I was replacing the plugs I climbed in and out of the engine compartment a couple times. Now my radiator leaks and I can't figure out where from. What did I do?.... :bang:

@skyline223 Check the top seam where the plastic tanks joins the metal fin portion of the radiator,that is where mine let go at.
 
Back
Top Bottom