What are you working on?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I finally got the painting finished on the camper. This took about a week to do because I had to put multiple coats of different paint water mixture to ensure a full saturation. You start with a 50/50 mix at three coats, then 75/25 two coats, lastly final paint color was two coats.

Still a long way to go, currently on the list is putting it onto the trailer, install the doors, building custom door trim rings, water seal rear galley door, connecting all the electrical, interior finishes, all the aluminum exterior trim

IMG_4188.webp


IMG_4190.webp


IMG_4185.webp


IMG_4183.webp
 
matzell said:
I know some of you guys had projects this weekend. Any progress or pics?
Click to expand...
Still waiting for time and no rain or snow to fix my brake line…

Chris came over to help me drink beer and burn all of the wood from my renovations last weekend. Just a small 6ft wide fire…

IMG_3596.webp
 
captainva said:
Still waiting for time and no rain or snow to fix my brake line…

Chris came over to help me drink beer and burn all of the wood from my renovations last weekend. Just a small 6ft wide fire…

View attachment 4043783
Click to expand...
Is that an actual fire pit? We had some homeless person make a fire next to our building the other night!
 
There’s a crappy concrete fire pit under there. Too lazy to cut things up
 
This weekend the 100 got a TPMS sensor replaced that failed at fall crawl. No more obnoxious blinking light! I also decided against swing outs for a lot of personal reasons and am going to run an interior tire carrier for the time being. Picked up a Bell Fab tire carrier on Black Friday and got it installed. Starting to prep for the 4x4labs bumper build. Waiting on a warmer day to clean up the spare before moving it inside.

IMG_5586.webp
 
jmurunner said:
This weekend the 100 got a TPMS sensor replaced that failed at fall crawl. No more obnoxious blinking light! I also decided against swing outs for a lot of personal reasons and am going to run an interior tire carrier for the time being. Picked up a Bell Fab tire carrier on Black Friday and got it installed. Starting to prep for the 4x4labs bumper build. Waiting on a warmer day to clean up the spare before moving it inside.

View attachment 4043805
Click to expand...
I love a rear tire mount …would like to have the same setup in the 80 bit I also love my drawers

IMG_8101.webp
 
A couple late late nights in the garage with yellowjackets and football this weekend. Bumper and winch are complete. Just have to mount up my old LED spots later tonight and the figure out if I want to tackle wiring up the DRLs, signals and fogs to factory wiring.

Waiting on a few more misc. lift parts to arrive this week to get her up in the air on 35s.

And finally the White Knuckle truck should hopefully arrive soon!

IMG_1493.webp


IMG_1492.webp


IMG_1494.webp
 
Toyodajunkie said:
Which set did you end up getting?
Click to expand...
I just bought the long side FJ60 inner shaft. The short side and the outers from my 40 will be reused in the 62 series front housing. They are 30 spline Chromoly and I have the 300m hub gears.
 
matzell said:
I just bought the long side FJ60 inner shaft. The short side and the outers from my 40 will be reused in the 62 series front housing. They are 30 spline Chromoly and I have the 300m hub gears.
Click to expand...

Nice! That’s gonna be sweet
 
Are you doing 3 link? I thought the radius arms were already the limiting factor for flex
 
You must log in or register to reply here.

Share this page

Back
Top Bottom