Water Leak

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 30, 2006
Threads
73
Messages
681
Location
Columbus, OH
I read lots of threads regarding water leatks but did not find this exact situation. I am getting water in the very back drivers side. Yes the jack is rusting. I saw a couple threads about the plastic pins leaking. My leak appears to be comming from where the two seams join in the very top just underneath the window. the whole chanel along the seam l seems to be wet. I took a look outside and noticed that there is a nice gap between the window seal and the seal on top of the body. I think I even see some metal. Please see attached picture. I am thinking about getting out my calking gun and injecting the whole gap with some black silicone rubber. Is there a better solution to this problem? Thanks for any suggestions.
 
I am looking at a 97 to buy and the same window is leaking into the jack holder.
tested it with the hose and water was pooring in.
how much does it cost a glass specialist to remove and reseal the window?
thanks
bird
 
I recall that you can purchase a new seal around the rear windows.

I would contact CDan and perhaps have a window shop install if you were not so inclined to do it yourself?
 
I went out tonight with my flashlight and my wife's makeup mirror. My neighbors probably think I am nuts lol. The drip is to the rear, about 1 or 2 inches before the back curve in the window. That is exactly where the belt moulding stops. There is about a 1/8 inch gap between the belt moulding and the rear vent assembly. Would it be seeping in this gap? Also, I pried the rear vent and looked inside. There is small amount of water running down the side. Should I seal the edges of the rear vent with some silicone rubber? Any suggestions would be greatly appreciated.
 
I went out tonight with my flashlight and my wife's makeup mirror. My neighbors probably think I am nuts lol. The drip is to the rear, about 1 or 2 inches before the back curve in the window. That is exactly where the belt moulding stops. There is about a 1/8 inch gap between the belt moulding and the rear vent assembly. Would it be seeping in this gap? Also, I pried the rear vent and looked inside. There is small amount of water running down the side. Should I seal the edges of the rear vent with some silicone rubber? Any suggestions would be greatly appreciated.

I have the same gap. On both sides of both of my 80s. The long piece of metal trim has some forward/back play. I would seal the plastic holders and not anything else. After I did this, the leak went away. Replacing the trim works equally well.
 
Last edited:
I agree with Aim. But I do recall reading a thread about resealing the sliding window. Gook luck
 
I sealed the plastic holders and a day later washed the vehicle. I went out of my way to wet the window down, and not a drop of water leaked inside. Of course, 2 solid days of rain may be different but I am optomistic. I did seal the gap in the window but then decided to run a small screwdriver down the window track and found some water drains within the window track. I realized that I just sealed in the water that drains from the track. I promptly removed the silicone from the gap. That gap must be there to discharge the water from the drains. Thanks everyone for your input.
 
thanks for the followup i have noticed this on my 91 and was having trouble finding the leak, so for the mean time i installed (drilled a hole) in the bottom on both sides so it would atleast drain
 
I finally fixed my leak. Sealing the Plastic pins didnt fix the problem. I had a small gap in the plastic vent thing behind the rear window. The water was running off the gutter, and and directly into the gap. I pulled the plastic out a bit and filled the gap with RTV silicone which "Glued" and sealed the vent. Since then its been through lots of rain and not a leak. I didn't see this resolution on any of the treads I read so feel the need to add it.
 
I stand corrected. Learn something every day...
 
Back
Top Bottom