water found in jack holder

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 27, 2006
Threads
53
Messages
377
Location
Northern VA
In the midst of beginning my drawer system project, I pulled the left rear interior panel and found water sitting in the mount that secures the OEM hydraulic jack.

Has anyone else found this in their 80?

I've done some preliminary tests by soaking the roof, sunroof area specifically, and around the rain gutters and left rear sliding windows.... no leaks found. I also tested the left rear sunroof drain and found it flowing without issue to the exterior outlet behind left rear tire.

Anyone have any suggestions? It'd be helpful while I got the panel pulled.
jack_holder_800x800.webp
 
someone could have put in the jack wet once.

also some condensation could have appeared between steel jack and rubber

i wouldnt sweat it unless you look into the bottom of the well and see evidence of water there as well....otherwise id guess its one of the above two.
 
Sliding window is a good guess, but I also had a leak on my rear hatch seal. It is the rubber gasket that is stuck or glued down that hatch seals to when shut. Mine was leaking in the upper left which caused my carpet to be wet and the jack holder area to have water as well. Purchased a new seal from CDan and problem went away.
 
I have the same problem, and I think it's coming from my sliding window. The water gets in past the window seal and drips down the plastic compartment cover into the jack holder. I haven't figured out what to do about it yet.
 
Thanks for the replies, fellas.

I forgot to say that when I found the water in there, it was a good half inch deep.

There had also recently been a couple of days of hard rain. But no water was found down in the well on that side.

I did take the 80 thru a car wash with a high pressure rinse cycle about a week ago. When the rinse jet passed by the sunroof, I put my hand up there and found it wet, like water was blown past the rear seals. I've noticed that I can depress the glass down (when closed) by putting pressure on it from my hand. I did also notice that the rug around the left rear tirewell was wet, but couldn't find any other wetness above it or in the left C-pillar.

My concern obviously is that water will get down in that area after i install the drawers and could rot the wood.
 
You guys really don't know that this is a common issue??

I saw the thread title and figured, "Meh, I'll let someone else get it." Don't MAKE me come over there and search FOR you! :D ;)



('Course I will search for ya if you really can't find what I'm talking about...:))
 
CJF,

You know, it's my 39th Birthday today and I took the day off to work on my 80 and have found myself in front of the computer today doing mostly searches in the IH8MUD forums.... so when I saw your reply initially I was about ready to just call you a smart ass and say something like, "If I'd found it initially, do you think I'd be wasting my day still rather than just post a question to get some immediate help?"....

And then I took a breath and reigned it all in. I returned to the search page and entered the following keywords: water, leak, jack, holder.

What I found was likely the very posts you were looking for.

https://forum.ih8mud.com/showthread.php?t=25521&highlight=foam

https://forum.ih8mud.com/showthread.php?t=75308&highlight=water+leak+jack+holder

So I will say this, you were correct. But emphasize my position, I've now spent another 20 minutes inside the house rather than out at the truck.

I'll tell ya what, this is what I'll do if find a question posted that I have an inkling has already been covered in a post.... I'll reply with the actual post link or atleast the known keywords that are likely to produce a good hit. Otherwise, I'll just be subjecting another mate down an endless ADD hole of one more thread search. But hey, that's just my perspective.

Anyone still trying to sort out this leak issue, I'll summarize some areas to check:

1) The gas cap area for a leak in the gasket
2) The left rear sliding windows' weep holes

I'll go check it out and post what I find.

CJF, at the end of the day no harm done by you and nothing personal. I noticed your intent to just kid about "go do a search". You just happen to be that guy after I've read too many folks that are not so subtle on the topic.

Sorry, brother.
 
Don't know what to tell ya.

I saw the thread and noticed it was going nowhere. I knew it was a common issue and that the answer was out there, but I would have had to search for it same as you. (And like I said, I would have if you really couldn't find it.) It probably would have taken me the same 20 minutes it took you.

Would you really rather I'd just not posted??

Happy birthday,

Curtis
 
As I wrote at the end, Curtis.....

Nothing personal, you happen to just be that guy with the reply.

i am glad you replied, because had you not, I wouldn't have gone back and done another search and found what I did.

Given the subject... water under the bridge pal.

*** Update:

I just went out and soaked down the truck. Concentrated on left rear exterior and hatchback. In particular the gas tank lid and rear sliding windows.

Suffice to say other than barely a trickle from a plastic piece that I hosed down after opening the gas tank lid (the cover, not the cap)..... nothing. Bone dry.

I'm at a loss. But I thought I let you guys know what I found.

Cheers.
 
I just went out and soaked down the truck. Concentrated on left rear exterior and hatchback. In particular the gas tank lid and rear sliding windows.

Even the plastic vent behind the sliding window? Now I am surprised. Another possible point is the actual rubber gasket that the windows slide in. It tends to separate right in the back, about half way up.

Very weird that you can't re-create it.

Curtis
 
Another spot... The louvre. Those black plastic vents back beside the window cover rubber flapper valves that are supposed to only let air out of the truck. They have been known to leak under up-in pressure washes.

Don't try to pull that plastic bit off from the outside. It is serviced from inside the truck behind the rear pillar headliner IIRC. A real PITA. Wait until it gets dark then shine a flashlight up inside the slots and you should be able to see the rubber flapper valves.
 
Yeah, i soaked the whole area.

It is irksome that I can't find any significant leak. Hmmmm. I mean, how else would that jack holder be full of water? This of course is a rhetorical question at this point. But I'll go back out and inspect the gaskets again.
 
Do you have the FSM?

Looking at mine, I would think that if you go as far as step 5 in the "Removal of quarter window glass" section, the problem would (hopefully!) have to be obvious.

Curtis
 
I have the FSM, but not the detailed electronic version.

I'm headed back out there and will try the flashlight suggestion made by Grench.
 
In regards to my rear hatch leaking I had to remove the D pillar plastic where the seat belt mounts and I removed the rear rail at the carpet and pulled it up at the corner. I was in the rig with it shut while someone soaked it with water and that is how I found the leak, it was running behind the D pillar plastic down to the carpet and jack storage area.
 
Ok, looks like I found it!

When I focused a pressurized stream on the left rear louvre and midpoint of the back most sliding glass, I found water inside. It was running in the area consistent with the pattern of getting the carpet wet only in the back left area, as well as in the jack holder.

One obvious leak point is where the gasket on the sliding window separates near the rear latch. That's by design, eh?

As for the louvre, did I read in one of the posts where this actually fixable?

Either that... stay outta car washes.

Thanks for everyone's help.
 
So Toy350,

It sounds like your truck was leaking from the louvre vent as well. What did you do to fix it? Not an easy area to work in from what I can see.
 
It isn't as bad as it looks -if- you remove the cover from the inside. My PS vent cover is hanging on by only the top of two bolts as the bottom one was a bit modified by trail.

What would be cool is if someone made a left and right stamped steel replacements for the plastic cover bits. They're a bit fragile IMHO.

I'm betting one of the louvre flaps is dirty, missing or broken. Shine a flashlight up through the vents and look up. You should be able to see them somewhat.
 
Check around the quarter panel belt moulding clip holes.
 
Dan,

Not sure I'm clear on what you're referring to with the "belt moulding".

Inside at the seat belt mounts on the D-pillar, or outside that hold the rear sliding window's trim skirt to the body?
 
Back
Top Bottom