Wasatch Cruiser Heads

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 6, 2007
Threads
13
Messages
130
Location
Newport Beach, CA
Hello all,

Unfortunately my living situation is not conducive to working on my '95 cruiser. I really need to replace all of the fluids, from the engine to the diffs. Also i would like to replace the right rear wheel bearing and clean and repack the other 3, lube the chassis etc. etc. While we are at it, i would like to inspect the rear flanges/drive shafts for deformity. Also and this is important, i would like someone's expert opinion on whether or not i should replace the seals around the front knuckles. I have been told that mine are fading fast. I am not by any means a mechanical whiz. In fact i probably suck. When it comes to working on my KTM that is another story but i am a total greenhorn regarding mechanical issue with my cruiser. If anyone is willing to help me out and has the space/tools etc. to work on a cruiser, i would be willing and would prefer to pay you instead of the dealer or will supply a hell of alot of beer and treat you to a hell of a lunch/dinner. I live in downtown salt lake in a condo/loft. Hoping to get a house soon. My email is gfox777@comcast.net. Cell is 801.330.5283. Tried to contact the guys at the wasatch cruiser club but the website does not allow you to contact them without being an official member. Anyone in the local area please help. -Greg Fox
 
Greg,

Not that I have been stalking you but don't you have a non usa 80? specifically from VZ? Are there any issues with parts dissimlarities? i am no help in that i sold my house and don't have room myself but i'm sure someone step up. you can join the forum without being a member so go sign up. i'll post a link to this thread for you.
dmc
 
Thanks

Hey Dave. Apprecaite you getting back to me. I live downtown in the broadway lofts. No way really to work here. Going to look for a house in the near future but am monitoring the housing slump and mortgage market implosion. I believe that we are going to see home prices dip a little and dont want to make the jump just yet. In any case, i do have a mechanic (#3) i use to do basic stuff. He does not charge a lot but he is no specialist either regarding cruisers. If i have to have him do the work, i prefer to buy all the parts and oils myself. Do you have a place where you go to buy stuff? You are right about my rig being from VZ. I am still working on the pulling to the right issue too. Since my last post to the thread that my good buddy Alvaro started, i have put on new tires, balanced, taken it to mark miller toyota for a 2nd opinion and am kind of stuck. According to them, the axles, caster, camber, thrust etc. are all within acceptable spec. Thus the alignment is not that bad at all. I was going to have them replace the right wheel bearing which is bad. My alt mechanic (#2) said as you recall that the rear axle is bent downward an inch on the left rear. The toyota mechanic (#1) did not confirm this. So i am just going to eliminate one thing at a time and if all else fails, i will drive to Colo to have Christo at Slee help me out as nobody here is good enough to identify exactly what the problem is. Repacking the other bearings and checking said parts probably will help a little. And who knows, maybe i have something loose around the knuckles? Thanks again for getting back to me. Look forward to wheeling with you one of these days. --Greg
 
Will Carroll

Cory,

I tried to get in touch w/ will Carroll a while back. Sent him a PM and spoke to Ryan Davis not too long ago who said that he would pass along a message when he spoke with him but no luck. If you know how to get in touch with him, can you ask him to call me or email his numbers so that i can talk with him? Appreciate it.

Greg
 
expedition america

Dave,

We should hook up bud. When i drove back from Venezuela, i shipped my car to panama and drove up through central america. UNREAL trip. I wish that i was still on the trip. Have been dying to drive to Ushuaia and had i known that you were doing this trip sooner, i might have been able to join you. Darn!

Greg
 
Just out of curiosity, You didnt have a Blue 60/62 series for sale some time ago in the same location?
Im no use on space, Im all full, But there are usually people around willing to help out, Myself for one.
Good luck on your search.
 
Thanks anyway Brian. No i did not have a blue 60/62. Going to try a few more people and then just bite the bullet and get things done with my mechanic. Probably see you one of these days though.

Cheers

Greg
 
Hey Greg,

I'm not about to say I'm an expert on Cruisers, but I've rebuilt front and rear axles a couple times.... I've got a two-car garage and I think all the tools to get a job like this done. I live just down the way in the East Millcreek area. I've been wanting to replace all my fluids and at the very least re-pack my bearings. Be good to have another Cruiserhead around to be wrenchin' with.

Plus, I'd love to talk to you about VZ... ;)

-Ferg-
 
Back
Top Bottom