Vortec Replacement...Let the Fun Begin

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 7, 2006
Threads
11
Messages
84
Location
Savannah, GA
Some backround... I have a '70 FJ40 that had a SBC installed by PO circa ~1988. I bought it in 1992. The only upgrades I've done have been dual batts, 4 wheel disc, shackle reversal, 2.5 lift front and 4 in the back, rebuild my old fried wiring harness from scratch and put in new seats.

My SBC finally said it had enough.. Bad cylinders on 1 3 7 (previous thread). I could have rebuilt it but I figured what the hell I need a challenge....:rolleyes: WHAT WAS I THINKING:rolleyes: . After reading plenty o' posts here and at pirate I decided to go with a vortec 5.7 replacement from a 1998 1500 Silverado (rolled) 63K miles on it. I got the whole shebang (harness, exhaust, brains, motor...)

I figured my challenges would be standard wiring (which I know enough to be dangerous), fuel, exhaust, and cooling along with misc stuff.

So here it goes..:D
My 40, the motor, and the motor mounts I used (same as previous) FJ Front.webp

motormounts.webp

Vortec.webp
FJ Front.webp
motormounts.webp
Vortec.webp
 
Tease.....;p

















Keep us posted......:bounce: :bounce2: :bounce:
 
I removed the old motor and installed the vortec. Not before I replace the oil pan gasket, and rear main seal. Since it was easily accessible.

I figured since there was already a 350 in there, I'm going to use the same motor mount position as before. I thought about re fabbing motor mounts but since the rest of the drivetrain was already in SM465 to stock 3 spd and I haven't had any problems I'd press.

1st up... Cooling
I had a four row already so I'm not going with aluminum, which I entertained. I'm going to stick with what I know works.

Fan options: Keep the mechanical fan in there (1st chioce)
or go with an electric which I already wired in case I wanted to switch. I figured the taurus fan (integrated shroud on 90-95 w/ 3.8l) has some believers so I researched that option (2nd choice)

Shroud... I had one but trashed it and my old mechanical fan when a blade then 2 let loose and shelled my shroud and radiator...awesome!! So I need one cause with the extra HP/Torque from the EFI I don't want any problems w/ cooling. I thought of fabbing one out of aluminum (not to difficult)

PROBLEM #1 No :censor: fan/radiator clearance with old rad mountsSide profile rad.webp

Not a problem I'll just move the mounts... right. Wrong.. After measuring I realized there was no way the mechanical fan could stay....It just wouldn't fit. Looked at the clearance from firewall to distro cap....6". 3.5" more than what was in there before:confused:
valve cover to firewall.webp

The valve cover to firewall measurement was 4"
The fan pulley only to the front frame was 5.25"

The Taurus fan can be trimmed to ~3" so it might fit But I'm still going to have to remount me rad...:doh:

Well that solved my shroud problem:whoops:

So I'm going to get a electrical fan and remount the radiator...more to follow. It takes me a while to get anything done so don't stay up at night looking for updates. I'll update as soon as REAL progress is made.
Side profile rad.webp
valve cover to firewall.webp
 
For the fan problem, check out a Volvo /bosch fan. They pull alot of air and are much thinner than the taurus. They come with a shrould that is just an inch or so larger length wise than the stocl rad. They are one speed.
 
Out of what vehicle? Volvo....??

You know I am not sure and I am a Volvo nut. I purchased it from a guy off ebay. They were a recalled fan because of a relay problem. The guy must have worked for a dealership and got the takeoffs. He removed the factory relay and sold them. I know it wasn't the 700 series because the fans on them are pushers. I will see if I can find a link to the guy and post back.
.

Here is the fan I bought. I am not sure this is the same guy, but its the same ad and fan.
http://cgi.ebay.com/ebaymotors/Radi...ewItemQQcategoryZ33600QQitemZ8050923073QQrdZ1
 
Last edited:
My wife has a 2001 Volvo V70 station wagon that recently had the fan replaced under recall. Could be the same model under discussion here....
 
Need Options...

My previous owner mounted the motor 8" (see pic)on center from the rear or the shock tower. I've read in some threads 8-12". With the motor being mounted so far forward, neither my clutch fan nor my Efan will fit w/o some serious mods (see pic). The fan/water pump clearance pic doesn't show 1-2" of forward lean of my front bib just to get the fan in there.
Im looking for some options besides RE-mounting the drivetrain. I had a SBC in their before however the difference being the serp belt and the deeper accessory rack.

1) trim the taurus fan and mount the rad support WAY forward as to sit on the front xmember support (have to reweld some support brackets. If that worked it would be TIGHT to say the least.

2) find a "shorter" water pump and pulley. As you can see the fan/rad would clear if the WP pulley wasn't so :censor: deep/forward
3) say:flipoff2: remount everything which I really am not in the mood for...what a buzz kill. Like I said the drive train has been working fine for the 14 years I've owned it even with an SM465 upgrade/replacement.

Anyone think of other options?? Any assist would say me from :crybaby: ..;)
Cheers
7in.webp

fanclearance.webp
7in.webp
fanclearance.webp
 
seems like to me if you can get the radiator moved forward a bit everything would fit? Can the brackets be cut and rewelded and moved forward? a few inches and it looks like you would be good. The only other thing I can think of is finding a slimmer radiator.

Noah
 
Ditch the serp belt setup for the old setup, it'll fit, mine is close and hasn't hit in 2+ months I've had the setup. IMHO, don't change the drivelines if they work good, I have spent way too much time tracking down vibrations.
Fan1.webp
 
1973Guppie said:
seems like to me if you can get the radiator moved forward a bit everything would fit? Can the brackets be cut and rewelded and moved forward? a few inches and it looks like you would be good. The only other thing I can think of is finding a slimmer radiator.

Noah

I'm pretty sure I can make it "work" but I'm it will be :flipoff2: tight.
 
id move the engine backward and keep the stock Belt setup.. That could be a real Pain in the ARSE to track down all the stuff needed.. then you need an old school short water pump..

shorten/lenghten Driveshafts is a pain, but not worth all the other hassles IMO..
 
There is no way I would ditch serp for V belt thats a bad idea IMO. Move the engine back if you gotta. Its not hard just a bit time consuming
 
HogDriver said:
Fussy,

Did you pull off all your surp pulleys and replace them or what? Can you expound on "old Stuff"?

Basically, did you take your old stuff and put it on the vortec?


Well, technically no... (sheepish)
I almost have a whole set of the v-belt stuff for the new 305 I am building. But looking at your pictures, if you replace the serp belt with the v-belt setup off of your old engine, it stands to reason that it will fit. Again, IMHO, don't mess with the driveline angles if you have it dialed in the way you like it.
 
Back
Top Bottom