vaccum on 2f ?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 4, 2004
Threads
52
Messages
208
Location
Ste Genevieve missouri
What do you do with the two vaccum fittings on the thermostat housing when you remove the rest of the smog stuff? They are two fittings on the bottom of the housing and each one has two fittings. Can I simply remove them and plug them? Also what is the function. Thanks, Bill
 
Those are thermostatically controlled vacuum switching valves, or V S V’s.



When the engine reaches certain operating temperatures the valves inside those pieces port the vacuum to other locations on the engine.



You do not need to cap the ports, they will not leak fluid. ;)


You can remove the valves from the lower part of the stat housing and install plugs.





Good luck!


-Steve
 
I don't know what year 2F you have, but those are not really "smog stuff"--they're "power stuff". The fitting on the thermostat housing is called a TVSV (Thermal Vacuum Switching Valve). One of the two ports on the TVSV is connected to manifold vacuum, and the other goes to your AAP pump on the carb. There should be no other connections (this system is controlled only by coolant temperature, not the vacuum switching valve or anything else)

Here's how it works: The vacuum switch inside the TVSV is open when coolant is below 122 deg F. Therefore, when the engine is cool, the manifold sucks all the way to the AAP valve. When manifold vacuum increases and decreases (by you opening and closing the throttle with your right foot) while the TVSV is open, the changing vacuum operates your AAP diaphram and squirts extra fuel into the carb on acceleration. In other words, it gives your carb an extra boost of fuel when the engine is cold. When the engine warms up, the valve inside the TVSV closes and isolates the AAP from the manifold vacuum, so it does nothing.

So keep it.
 
I think AAP stands for Auxiliary Acceleration Pump. When the AAP has high vacuum acting on it, its diaphragm is pulled out and draws fuel out of the carb float bowl into and into the AAP's cavity. When the vacuum decreases (when you open the throttle), a spring pushes the diaphragm back in, squirting the fuel out of the AAP cavity and into the carb barrel. And the tractor goes faster.

Next week, we'll learn all about the throttle positioner, but not until Toad figures out the damn signal from the speed sensor. Grrrr

Hey, Poser: my tech contributions are so few and far between that when I actually know something, I have to make the most of it.:flipoff2: ;p
 
Mr. Toad said:
I think AAP stands for Auxiliary Acceleration Pump. When the AAP has high vacuum acting on it, its diaphragm is pulled out and draws fuel out of the carb float bowl into and into the AAP's cavity. When the vacuum decreases (when you open the throttle), a spring pushes the diaphragm back in, squirting the fuel out of the AAP cavity and into the carb barrel. And the tractor goes faster.

Next week, we'll learn all about the throttle positioner, but not until Toad figures out the damn signal from the speed sensor. Grrrr

Hey, Poser: my tech contributions are so few and far between that when I actually know something, I have to make the most of it.:flipoff2: ;p




I am here to learn bud; there is an immense knowledge base out here that I am grateful for every time I log in. I learn things every day out here, and it is a great thing!


I was not giving you s***, I just like spelling things with a K where a C belongs every once in a while… :)




I, as I am sure many others, appreciate your knowledge shared.


:beer:
 
Poser said:
I was not giving you s***, I just like spelling things with a K where a C belongs every once in a while… :)
I didn't think you were. And spell it however you want because what you said is true for me too: "there is an immense knowledge base out here that I am grateful for every time I log in. I learn things every day out here, and it is a great thing!"

:beer: to Mud
 
Bill,
On your 78 2F the BVSV's in the T-stat housing can go away and be replaced w/ 3/8NPT allen plugs. Their original function was to control EGR vacuum and to keep the distributor from getting full vac advance.

Toad is correct about AAP, but Cruisers only had AAP for about 8 months in 1975, so it does not apply in most instances. Various other carbureted Toyotas had AAP for most of the '70s and '80s.

BTW Bill, I am working on the carb, but it is a few days away from going out the door.
 
Thanks for all the replys.
Jim, I will go ahead and plug them up like you said. Don't worry about the carb, I am not in a hugh hurry. While it has been down I have taken the time to attend to many small items that have been looming at me for the last several years. Since I can't drive it I might as well tinker. Bill
 
Back
Top Bottom