Turn Signal Issue

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 5, 2007
Threads
20
Messages
93
Location
Milwaukee, WI and Louisville, KY
Hi All-

Having a little annoying problem with my LC. When ever the headlights are on the left turn signal doesn't work (the light just stays on). Turn the headlights off, everything is fine.

Hopefully not a sign of a larger problem.

Peace.
 
Check the ground wires in the area of your signal, widen the search from there. Sounds like one is disconnected or something.

-Spike
 
The problem might be at the switch itself, since both of those functions work off of the same stalk to the left of the steering wheel. Spray some contact cleaner right on the switch (at the base of the stalk) while putting it through its motions. You might get lucky. ;)

Curtis
 
Thanks. I will try that and report back. My better half is driving it right now. (She loves the truck) When she gets home I will run and get some spray. I think the issue just started, as I have driven it with no problems.
 
I'm with Spike - check the wires for something that worked its way loose, especially given that it just suddenly started happening.

Also, have you (or any previous owner) done any mods in this area, like the turn-signal / front marker mod (so the marker light also blinks with the turn signals for better side visability)? This might also be a source of loose wiring.

Good luck!
 
So I'm finally getting around to this. The problem seams to be that when the lights are on the left signal stays on the entire time.

Where is the switch located at?

The switch I was talking about is right at the base of the stalk/arm used to turn them on.

Although... I have to admit that after your earlier posts I thought about it some more and kind of doubt that's the problem. But, won't hurt to check it! :)

Curtis
 
The switch I was talking about is right at the base of the stalk/arm used to turn them on.

Although... I have to admit that after your earlier posts I thought about it some more and kind of doubt that's the problem. But, won't hurt to check it! :)

Curtis

Yea. Me too. My life is never that easy. :)
 
Have you checked the flasher?
 
Since I have not driven it in awhile, I let this go. Went for a drive last night. The problem got worse! Now neither turn signals work. I'm thinking the switch went bad. It is a 91 after all. How hard is that to replace? I'm sure someone on here has done it.
 
Did you try hitting it with contact cleaner, or even wd-40, just for giggles?

As for replacement, you can either replace the "combination switch" which consists of all the stalks/switches (turn signal, wipers, cruise control, etc.), or just the individual stalk/switch that's malfunctioning. The first option is of course more expensive, but it's plug-and-play, while the second option is not. (It requires pulling the specific pins from the harness connector, and also disassembling the combi. switch to remove the specific switch.)

Oh, and if you go with replacing the combi. switch, you get an automatic upgrade to variable-timed intermittant wipers. :D (Seriously.)

Curtis
 
First thing I'd do is get the trailer module out of the circuit. It's a small box inside the right side rear fender behind the tail light. All those lights go through that box and it could be causing problems.

When you get back there it's as easy as unplugging the module and then plugging the factory plugs into each other. There is also a single wire that runs along the floor over to the left tail light and you would want to remove that as well.
 
Did you try hitting it with contact cleaner, or even wd-40, just for giggles?

As for replacement, you can either replace the "combination switch" which consists of all the stalks/switches (turn signal, wipers, cruise control, etc.), or just the individual stalk/switch that's malfunctioning. The first option is of course more expensive, but it's plug-and-play, while the second option is not. (It requires pulling the specific pins from the harness connector, and also disassembling the combi. switch to remove the specific switch.)

Oh, and if you go with replacing the combi. switch, you get an automatic upgrade to variable-timed intermittant wipers. :D (Seriously.)

Curtis

I tried the contact cleaner. No change. Also it seems like the cruise control wont engage now. The light comes on but won't keep the truck at speed. Looks like the whole thing needs to come out.

Any idea on pricing for that "combination switch"?
 
Any idea on pricing for that "combination switch"?

Spendy for sure.

Read landtank's post again and follow his suggestion. The lone wire that he mentions running across the floor is in the cargo area, just inside the plate along the rear sill. This wire was run at the port for those vehicles that got the hitch platform and it is notorious for shorting on the metal lip where it goes into the right wheelwell.

As Rick mentioned, the trailer modules are prone to failure and will give the symptoms you describe.

-B-
 
Ok I found the little green wire that runs through the cargo area. Traced it back to the area behind the DS rear tail light. It goes into a group of wires that head up towards the tail light. These wires appear to have been tampered with at some point, as there is some electric tape around them near the middle. Where is this box I am looking for from that green wire?
 
Those are the wires to the port installed black box that controls the trailer connector. It should be back there inside the PS wheelwell.

-B-
 
Those are the wires to the port installed black box that controls the trailer connector. It should be back there inside the PS wheelwell.

-B-



OK. Now that I looked on the PS. I found the box. See pics. It looks to be all burnt and melted on the one side. It doesn't look like you can remove that box with out cutting the wires.
img2081wc7.webp
img2082au7.webp
img2084zi3.webp
 
one set of wires goes to the 4 pin plug out at the receiver, the other set gets wired into the truck's harness. If everything is taped with electrical tape I'd say some hack installed the box. My guess would be that he just "T"d into the harness. You'll need to remove all that tape and figure out how to put it back in shape. But from the looks of it you have found your problem.
 
one set of wires goes to the 4 pin plug out at the receiver, the other set gets wired into the truck's harness. If everything is taped with electrical tape I'd say some hack installed the box. My guess would be that he just "T"d into the harness. You'll need to remove all that tape and figure out how to put it back in shape. But from the looks of it you have found your problem.

The taped up area was on the other side (DS). The box and melted area are on the PS of the truck by the wheel well. How can I remove the box? Would it work just to cut the wires and remove the box and reconnect them to each other?(Obviously each color together) Your other post said something about removing the green wire that runs through the cargo area? Should I leave that disconnected?

Thanks for all your help guys. I'm obviously a newbe that is enjoying the tinkering.
 
Back
Top Bottom