- Thread starter
- #41
not quite sure? I'll see if I can weigh it somehow... I think I have a scale in the garage...
here are the light tabs.
Tube Bender is ready!
- Thread starter DiscoveryXD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
not quite sure? I'll see if I can weigh it somehow... I think I have a scale in the garage...
here are the light tabs.
Matt,
I was curious as to why you went with a mesh floor and not a solid (1/8" alum) material for the floor? The air noise from a mesh floor can be quite annoying to say the least! Rack is looking great so far.
I was curious as to why you went with a mesh floor and not a solid (1/8" alum) material for the floor? The air noise from a mesh floor can be quite annoying to say the least! Rack is looking great so far.
- Thread starter
- #43
Thanks!
I have the same mesh on my other rack, and I've had no problems with it before. The rack is noisy with out the mesh, so it doesn't make much of a difference. Not to mention I've had a roof rack on the truck since I bought it so I don't really notice the noise.
I have the same mesh on my other rack, and I've had no problems with it before. The rack is noisy with out the mesh, so it doesn't make much of a difference. Not to mention I've had a roof rack on the truck since I bought it so I don't really notice the noise.
thats the least of the issues.
- Thread starter
- #45
oooooohhhhhh! burnnnnn! haha, it's part toyota, don't leave that out.
- Thread starter
- #47
You coming to the meeting next week?
I may have the rack, depending on the powder coating situation.
- Thread starter
- #49
that must mean you have someone turning wrenches on your new toy for free! 
that must mean you have someone turning wrenches on your new toy for free!
Gotta earn my room and board some how...but I work on LRs too
- Thread starter
- #51
Gotta earn my room and board some how...but I work on LRs too
really? your own, or at a shop?
Yeah, the bum is staying at my house.
Jack
NNNNNNNNNOOOOOOOOOOOOO!?!?!?!?!!
Say it isnt SO!
Is DARCIE locked away in her bedroom?
Som bitch is always hittin on the wives!
When are we grabbin a beer?
K
He's couldn't make it as a mechanic so he settled for engineering.
Nah, just work on my own and friends' junk....owing a LR really taught me how to be a mechanic
NNNNNNNNNOOOOOOOOOOOOO!?!?!?!?!!
Say it isnt SO!
Is DARCIE locked away in her bedroom?
Som bitch is always hittin on the wives!
When are we grabbin a beer?
K
I brought mine so she's all yours - quid pro quo
- Thread starter
- #56
He's couldn't make it as a mechanic so he settled for engineering.
haha, cause we all know that was the easy route!
Post up some pictures of your 40 so I can see the fenders!
Nah, just work on my own and friends' junk....owing a LR really taught me how to be a mechanic
I can feel the love!
haha, cause we all know that was the easy route!
Post up some pictures of your 40 so I can see the fenders!
I can feel the love!
I'd like them to be a little higher in the front.
The rockers will be trimmed about two or three inches up from where they are now. Maybe a half inche higher than where the angle iron runs now.
- Thread starter
- #58
ok, looks good.
Dropped off the rack this morning at Alltizer in carson, he said monday at the latest!
Dropped off the rack this morning at Alltizer in carson, he said monday at the latest!
- Thread starter
- #59
well monday turned into this afternoon.. that was quick! The lights are mounted, just didn't take a picture because it was late.
